Today when I attend meetings while on the job at Dell and the discussion is about something new, and the manager is looking for input from the team, I usually sit there quiety while the others share their thoughts. This is not my usual behavior as I am usually quick to respond with a quip or something sarcastic.
Later, after everyone else has given their two cents, then if asked, I will wade in with both feet. This hasn’t always been the course of action I would have taken. Actually, I used to be pretty hot-headed. I was usually the first person to respond when someone asked a question. I already had my mind made up about just about everything.
My wife began noticing a change in my behavior a few years after we were married. She would ask me a simple question, like, “Would you like a piece of gum.” I would suddenly go into a momentary comatose state where I would stare off into space and think about it. She would say something like, “The answer doesn’t need a lot of thought. It is either ‘yes’ or ‘no’.”
After careful analysis, I finally figured out what happened. The transformation began the day I entered the electric shop at the coal-fired power plant as an electrician. I described that first day in the post “New Home in the Power Plant Electric Shop“. In that post I described my first job as an electrician when I went to the coalyard with my foreman Charles Foster to fix a room heater that wasn’t working.
The first time I used my new tools, Charles told me to remove a screw from a fuse block so that we could lift a wire in order to replace the fuse block.
When I was removing the wire (with one hand, as Charles had warned me that an electrician never uses two hands to do this), the screwdriver slipped and shorted out on the mounting screw which caused a brief flash. In the millisecond that the flash occurred, it cut a notch in the tip of my new Stanley screwdriver.
This was the beginning of my 18 year career of various minor electrocutions and small explosions. We did things to minimize the chances of shorting out your screwdriver when working on a hot circuit (that means a circuit that has the electricity still turned on). One thing we would do is wrap rubber tape up the metal shank so that if it leaned against something metal with it while the tip was touching something hot, it wouldn’t short out the circuit.
Inevitably, something would happen every now and then and something was going to explode. So you just had to be prepared for that. This is where the “Prolonged Pause” comes in.
Sometimes there is nothing you can do. Let me give you a “For Instance”. One time when we had an overhaul on Unit 1 (we had 2 units at our Power Plant in North Central Oklahoma), Richard Moravek was visiting from the Power Plant in Muskogee, Oklahoma. I have written about him in the Post “Lap o’ Luxury at the Muskogee Power Plant“. Each morning at Muskogee, he and Jay Harris would sing the song, “Nestle’s makes the very best Chocolate”, with Richard whistling as he sang like the Nestle’s rabbit.
On one particular day, Richard and I were sent to perform a “quick and dirty” elevator inspection on the Unit 1 elevator. It received a lot of wear and tear during overhaul with everyone riding up and down from the 9th floor where you could reach the upper echelons of the boiler. If things didn’t work perfectly every time, then the work would be slowed, and schedules wouldn’t be met.
During our elevator inspection we decided that we needed to change out some lights on the push buttons, because…. well… because some of them were burned out. Which caused them to not light up when they were supposed to, causing some Power Plant workers to become confused because they would forget which button they had pushed when they entered the elevator, thus, allowing them to forget which floor they were supposed to get off.
Anyway, Richard had taken the screws out of the push button panel and had swung the door on the panel open so that the wiring inside was all exposed. He reached in to pulled out one of the push button assemblies so that he could remove the bulb (oh… electricians call bulbs, Lamps… I mentioned that in the post “Place On Light Duty at the Power Plant“, if you recall).
I had reached down into my tool bucket and pulled out a box of special elevator lamps….. Actually, I think it was a standard 6S6 lamp, but it looked like a bulb to me:
Richard had put his hand out to receive the bulb I had in my hand, so I handed it to him. At that point, a funny thing happened. You see, my other hand was on the elevator scissor gate.
As I placed the lamp into Richard’s hand, he suddenly twitched and sort of jumped at the same time. When he did, he pushed into me and he began doing a jig. My legs were twitching and I was sort of doing a jig myself, or maybe a jog.
It became apparent right away what had happened. While Richard’s one hand was in the elevator push button panel taking out the bulb, he had come in contact with the electric circuit. This was fine as long as he wasn’t grounded. That is, he wasn’t touching anything else metal, like the front of the panel.
Being a good electrician, Richard had kept his other hand at his side like Charles Foster had taught me my first day as an electrician. That is, until he raised that hand for me to give him a lamp. When my fingers touched his palm, and my other hand was holding the elevator gate, we suddenly made a circuit to ground. From Richard, to me, to the gate, to the ground, and back to the the main power generator through various grounds and circuits and transformers….
About the time that I realized what was happening, we had separated from each other, and were no longer dancing. It cracked us up and we stood there laughing about it for a minute because both of us had just been dancing in the elevator.
As I explained in the post about being on light duty that I mentioned above, when you went to work on the stack lights, you carried metal prod with you that you used to ground the large capacitors before you worked on the circuit. When you did this, there would be a bright flash and a loud explosion.
If a noise or a flash like that made you jump, you may end up going over the handrail and falling 500 feet to the ground. So, you learned that in the event of a flash, your first reaction is to freeze. Then assess the situation, and then if necessary, Panic.
Many years later (like 16), I became very aware of how well trained we were when something like this happened when I was once again working with Charles Foster in a junction box on the 11 landing of Unit 1 on the west side. We were standing side-by-side and we were working on something hot.
Suddenly there was a bright flash and a loud boom as something shorted out. By that time in our history, we had learned all about wearing fire resistant clothing, so that even though what we were wearing wasn’t fire proof, it also wasn’t going to melt to our skin.
What amazed me about this moment was that we both stood there still for a moment before we panicked. There was about a one second pause where we both restrained ourselves from jumping back. I chalked this up to our years of being around explosive situations. Jumping back as the first reaction can often lead to other injuries.
I took this resistance to panic with me into other situations. Before 1994 when OSHA added a bunch of new laws protecting people in confined spaces, I was crawling inside the main generator bus that goes out to the main power transformer. No hole watch. No one watching me outside that could grab me and pull me out if something went wrong.
I had squeezed myself into one of these pipes to clean the insulators that held the bus in place in the middle of the pipe. This meant that I was crammed into the pipe under the bus bar that ran through the middle of the pipe.
I had made it to the insulator that I needed to clean and wiped it down with the rag I had taken with me. Then I decided I couldn’t go forward anymore to look at any more of the insulators because it was too tight of a fit. So, I started to back myself out.
As I went to push myself back I suddenly realized that I was stuck. It was easy moving forward because I was using the soles of my sneakers to push on the pipe, but as soon as I wanted to go back, there didn’t seem to be anyway to maneuver my body in a way that would back myself out. This was one of a few times when I began to feel the panicky feeling of claustrophobia.
I had seen claustrophobia in others and I knew that when you are gripped with it, you can hurt yourself, or even Bob Lillibridge if he happened to be grabbing your legs at the time (see the post: Bob Lillibridge Meets the Power Plant Ghost for an explanation.
Here it came… I felt myself swelling up tight in the pipe as the panic was gripping me. I knew I had to do something quickly or it wasn’t going to be pretty…. Well, either way… nothing about this was pretty. So, I forced myself to calm down. I told myself to breathe out, and slowly back in.
Then I decided to use the palms of my hands that were stretched out straight in front of me to push against the pipe to move me back. With that effort, I could see (in the darkness) that I had moved myself back about 1/2 inch. I thought. “Ok, 1/2 inch is something. If I did that 100 more times, that would be more than 4 feet. 200 times and I would be out of this pipe.”
Realizing I could move myself at least a little bit allowed me to calm down and quell the panic. I did nothing but concentrate on pushing with my palms 1/2 inch at a time and eventually, I did climb out of that pipe (What you expected me to say I was still in there?).
I don’t know how many times over the years I have woken up in the middle of the night and swung my feet over the side of the bed and taken a few large breaths because I had been dreaming about being in that pipe again. I will discuss the top of claustrophobia in a later post, but this example fit the top of training yourself not to panic so I thought I would use it here.
If you ever end up talking to someone that doesn’t quite look at you when they look like they are trying to look at you, then you may think that they are a welder. There are some welders that seem to look at you from the corner of their eye. I suppose it was because the middle of their vision has been burned out because they have looked at the welding arc too many times without their visor down.
Similarly, if you ever encounter someone that momentarily goes into a comatose state for a few moments when you ask them a simple question, you may now think that maybe this person was a Power Plant Electrician that has learned to have a Prolonged Pause before they Panic… or.. well, respond to your question. If they aren’t, then they probably were just trying to ignore you.