After the reorganization at the coal-fired power plant in North Central Oklahoma during 1987, a bunch of new faces showed up at the plant. I mentioned in last week’s post that we had a new plant manager, Ron Kilman (See Post: “From Pioneers to Power Plant Managers“). In that post I also mentioned that the PC age was rapidly growing and I had bought a computer of my own and was eager to learn more. The Electrical Supervisor, Leroy Godfrey had retired, and was replaced by a guy named Tom Gibson. Tom was a good supervisor who was willing to think out of the box.
Tom gave me one of my first assignments directly by calling me to his office. Well, Leroy had never really called me to his office before. When Leroy wanted to chew you out, he was happy to come down to the Electric Shop and do it, so I didn’t really know what to expect by being “called to his office”. Believe me… it wasn’t the last time he had “called me to his office.” But it was the most satisfying time. Mainly because this time, when I arrived, Tom’s face wasn’t beet red with anger like it was on one later occasion.
This is what Tom told me to do… He said that we needed to install computer terminals all over the plant. They had a chart where they wanted the terminals to go. There were about 15 locations all over the plant including the coalyard which was about 1/2 mile from the main plant. Along with those, there were a bunch of IBM Network printers that needed to be installed with the terminals.
Then Tom told me the best part. He wanted me to do it all myself. Then he told me an even better part…. He said, (and I quote) “I want you to learn everything you can about this computer stuff. I think it will come in handy.” As my friend Stephen Todd at Dell would say, “That was the ‘Keys to the Kingdom”. I told him I would be glad to do everything he asked.
That last part later came back to haunt Tom…. but he did tell me…. learn “everything” I could about the computer. When he was referring to “The Computer”, he was talking about the company mainframe, a Honeywell system that resided in Oklahoma City at Corporate Headquarters.
The Terminals I was going to install were called “Dumb terminals”. they weren’t computers, they were just monitors with a keyboard that connected directly to a switch back in the telephone room that was connected via a microwave link directly to Oklahoma City and the Honeywell system:
So, when I returned to the electric shop, I began my “hacker” apprenticeship. One that would later allow me to harass Gene Day in the Control Room, confuse Dick Dale in the warehouse, cause headaches for the IT department downtown, and finally cause the President of the Electric Company to personally call our Plant Manager Ron asking who was this guy Kevin Breazile! Hence the reason for Tom Gibson’s beet red face a few years later. But that is another story for another time.
I had two things right away that I had to figure out. How was I going to run cables from the telephone room in the office to each of the places around the plant that needed a computer terminal and what are these funny connectors and what do I need to do with them?
Ok, so I figured they plugged in the back of the terminal and then there was a Cat1 cable (no, not a Cat3, a Cat1) that plugged into that, and needed to plug into a jack in the wall that I was going to have to install. They called these funny connectors “Hoods”. The 25 pin Hoods that we used were blue. We had 9 pin hoods also that we used for the actual PCs that the clerks and the chemist were using. They had an emulator program to make them act like a dumb terminal:
In an early post called “Power Plant Men’s Club Prizes and a Story of Luck” I explained how I have always been cursed with being very lucky. Well, that’s what some may call it, but I prefer to believe that one of my best friends St. Anthony helps me out at certain times. Well, this was one time when I asked for his assistance. St. Anthony of Padua is considered the Patron Saint of lost items. So, I asked him to help me figure out how I was going to do all this work in a reasonable amount of time.
As is often the case, St. Anthony pointed me in the right direction. This particular day, he told me to tell my problem to Charles Foster. My close friend and one of the two Electric Shop foremen (not mine. I was working for Andy Tubbs). So, during lunch I told him what Tom Gibson told me to do, and showed him the blueprints where they wanted the terminals placed throughout the plant.
One of the places that needed a terminal was right there in the electric shop office. Charles looked around the office and said, “You know what? there used to be an old intercom system in this office that I think goes up to the telephone room. In fact, I think all the intercoms that were originally installed in the plant went to the telephone room.”
I vaguely remembered the intercoms when I was working as a summer help as there used to be an old box sitting in the garage when I worked for Stanley Elmore. They were later cut out and removed, because it wasn’t really practical and so it wasn’t used. Charles told me to start there, because there were intercoms everywhere. In the control room, the warehouse, and even in the coalyard! And definitely in the office area. This was just what I needed to hear. My work was already half done.
I pulled the cables out from under the desk where they had been cut and checked them out. There were definitely enough cable pairs to do the job. In most places I had to install both a terminal and a printer, so I had a lot of dual wall jacks just for this job:
There were some places where the intercom system didn’t go where I needed to install either a dumb terminal or at least connect a computer. So, I was looking for any kind of alternate way to install the jack without having to run cables all the way from the telephone room to these locations. So, I went out and bought a book about networking so that I could learn more about what was really going on. If I had bought it a few years later it might have been called “Dumb Terminals for Dummies”, but the Dummies books hadn’t come around yet.
I have since thrown that book away after using it for years to prop up the corner of our sofa bed for the times when my mom would come and visit and she would sleep on the bed, only it had a broken bracket, and the Networking book was just the right thickness to level the bed…. But there was one page in the book that I found that allowed me to hook up dumb terminals in places where there was only a phone line.
You see. When the phone lines were run throughout the plant, they used a three pair cable. Well. A phone really only uses two wires (or one pair). so, this left 4 more wires not doing anything. The only problem was that the dumb terminal used 4 pair, or 8 wires…
So, when I was reading the networking book, I ran across a diagram that made me stop and stare. I like to think that I was holding a half eaten apple in my hand and I had just taken a bite when I stopped mid-bite and stared. It would have been a nice picture to remember sort of like when the apple fell on Newton’s head. Only we didn’t have cellphones with cameras in those days, so no one was around to take my picture. The diagram I saw was this:
What? This showed 4 of the wires are nothing but grounds…. The network cable only really uses 4 of the 8 wires. Which means I only needed two pair. And guess what? The phone lines run all over the plant were 3 pair with only one pair being used! So, I was able to install the computer jacks right next to the telephone jacks and use the same cable that the telephone was using, and they all tied back to the telephone room where the main computer switch was located that connected to the Mainframe computer back in Oklahoma City through something called a Memotec X.25 Modem.
So, now that I have gone through all this detail to tell you how I was able to quickly install all these terminals and printers around the plant in a way as if it is exciting (because it is to me). I know that many of you are so bored out of your gourd that you have already stopped reading before you have reached this sentence…. I suppose those of you that are still following along are wondering “Why?”
Why would we want to install all these dumb terminals throughout a power plant that connected to the Honeywell Mainframe down at Corporate Headquarters? Well. It was because all the plant operators, mechanics, welders, machinists, electricians, instrument and controls and heavy equipment operators were going to start using it to do stuff. Yeah. All of us were being introduced to the computer age. From the janitor on up.
Each printer had 4 character ID that identified it, so if you were looking at a work order on the terminal, you could choose to print it. You just had to know the 4 character number and you could print the work order out on any computer in the company. Usually, this meant, you wanted to use the printer that was closest to you. But if you wanted to print something out for the warehouse, as long as you knew their printer ID, you could send them a printout of some part that you wanted them to retrieve for you. Then call them up and tell them you printed something out on their printer.
Ok. So the average Joe didn’t see much benefit, but it did get them used to seeing computer monitors all over the place, which at least helped them in the future when the real computers showed up. Right now, they were just “Dumb Terminals” and that’s what a lot of the operators and maintenance people thought… they are just dumb…
I, on the other hand was in hog heaven. You see. I had called downtown to the IT department and asked to get a user name so that I could log directly into the mainframe. After all, my supervisor Tom had told me to learn “everything” I could about “this computer”. So, I took him up on it. I quickly was learning UNIX commands, though at the time, I didn’t know that’s what they were called.
I began learning the Computer language called “A” before I realized there was a “B” language and a “C” language, and that C was the one that was really used at the time. As it turned out the mainframe had manuals for everything right on it. That is how I was able to cause so much trouble the next few years.
Oh, and one more interesting thing I discovered on the mainframe. It had this interesting feature called “Email”. Yeah. Only, after figuring out how to pull up a list of all the emails on the system I found that there was only a handful of people that actually had e-mail addresses. So, the only person I would email on the mainframe was an engineer named Craig Henry. I had met him briefly once, but in the next few years, he was a valuable source of information. Email seemed like a great idea, but what good was it if there was only a few people you could send an email?
As for Craig Henry… As Humphrey Bogart said to Claude Rains in Casablanca, “This is the beginning of a Beautiful Friendship.” Come to think of it… Craig Henry sort of reminds me of Claude Rains… I must admit, I learned a lot more from him than he ever learned from me.