Tag Archives: filter

Angel of Death Passes by the Precipitator Door

Originally published on May 25, 2012:

Either this was the luckiest day of my life, or a day where stupidity seemed to be my natural state of mind. This particular day occurred sometime during September 1983. The Main Power transformer for Unit 1 had  shutdown because of an internal fault during an exceptionally hot day during the summer and was being replaced.

While the unit was offline, while I was on the labor crew, I was asked to help out the electricians who were doing an overhaul on the Precipitator. The Precipitator takes the ash out of the boiler exhaust before it goes up the smoke stack. Without it, you would see thick smoke, instead, you see only clear exhaust. At the time the electricians I worked with were Sonny Kendrick and Bill Rivers. I had already applied for a job in the electric shop and was waiting to see if I was going to be offered the job. This gave me the chance to show the electricians what a brilliant worker I was.

Bill Rivers told me to go in the precipitator and wipe down the insulators that held the wire racks in place. He showed me where they were. I wore a regular half-face respirator because the fly ash is harmful to inhale.

Half-face respirator

Just before I went in the precipitator door to begin wiping down the insulators using a Scotch Brite Pad, Bill Rivers pointed to my flashlight and said, “Don’t drop your flashlight in a hopper otherwise you will have to make sure that you get it out of the hopper before we go back online.” I told him I would be sure to hold onto my flashlight (noticing that Bill had a string tied to his flashlight which was slung over his shoulder) and I entered the precipitator door.

Yellow Flashlight similar to the one I carried

The inside of the precipitator was dark. 70 foot tall plates are lined up 9 inches apart. Wires hang down between the plates and when the precipitator is turned on, the wires are charged up to around 45,000 volts of electricity. The wires each have a 30 pound weight on the bottom to keep the wires straight, and the wires are kept apart and lined up by a rack at the bottom. One end of the rack which is about 25 feet long is held in place by an electrical insulator about 3 feet long. This is what I was supposed to clean. The light from the flashlight lit up the area around me because everything was covered with the fine white powder reflecting the light.

The first hopper I came to was full of ash up to the top of the hopper, but just below where the insulator was mounted to the edge of the hopper. So, I worked my way down to the ledge along the edge of the hopper and dangled my feet down into the ash as I prepared to wipe down the first of the four insulators on this particular hopper. Just as I began, the precipitator suddenly went dark as my flashlight fell from my hand and down into the hopper. — Oh boy, that didn’t take long.

Fly Ash Hoppers. Our hoppers were 12 foot by 12 foot at the top.

I sat there for a minute in the dark as my eyes grew accustomed to the small amount of light that was coming through the doors. After I could see again, I reached my hand into the ash to feel for my flashlight. The ash was very fluffy and there was little or no resistance as I flailed my hand around searching for it. I leaned over farther and farther to reach down deeper into the ash. I was at the point where I was laying down flat on the ledge trying to find the flashlight, and it was no where to be found.

I pulled myself over to the side edge of the hopper and dropped myself down into the ash so that I could reach over where I had dropped the light, but I was still not able to find it. At that point, I was leaning out into the hopper with only my one index finger gripping the ledge around the hopper. I had a decision to make… I thought I would just bail off into the ash to see if I could find the flashlight, or I could give up and go tell Bill Rivers that I had done the one thing that he told me not to do, and in record time.

I don’t usually like to give up until I have exhausted every effort, so here was my dilemma. Do I let go and dive into this ash to retrieve my flashlight? Or do I leave the hopper and go tell Bill? I regretfully decided to go tell Bill. So, I climbed up out of the hopper, with my clothes covered with Ash (as we did not have fly ash suits at the time and I was wearing my coveralls). I made my way to the precipitator door and once I was outside, I determined which hopper I had been in when I dropped my flashlight.

I found Bill and told him that I had dropped my flashlight in a hopper full of ash. He told me to get the key for that hopper and open the door at the bottom and see if I could find the flashlight. Unlike the picture of the hoppers above, we had a landing around the base of the hoppers by the access door so you didn’t need a ladder to reach them.

Curtis Love had been watching the door of the precipitator for me while I was supposed to be wiping off the insulators. He came down with me, and we proceeded to open the access door at the bottom on the side of the hopper. When I opened the door both Curtis and I were swept backward as a stream of fly ash shot from the door. The ash fell through the grating to the ground below. We regained our footing and watched as a tremendous pile of ash grew below us. If the flashlight had come out of the doorway, it would have remained on the landing since it was too big to go through the grating, but it never came out.

After the ash had finished pouring out of the hopper as if it were water, I reached down into the remaining ash to see if I could feel the flashlight. Still I was unable to find it. There was about 4 more feet from the doorway to the bottom of the hopper, so I emptied out as much ash as I could using my hard hat for a shovel. Then I pulled my body head first into the hopper and I reached down as far as I could in the bottom of the hopper, but I couldn’t find the flashlight.

So, in my infinite wisdom, I asked Curtis Love to hold onto my legs as I lowered myself down to the throat at the bottom of the hopper. I lowered myself down until I had half of my face laying in the ash. At this point only one of the two filters on my respirator was able to function as the other one was down in the ash. I reached my hand into the top of the feeder at the bottom of the hopper and with my finger tips I could just feel the flashlight. I had reached as far as I could, but I couldn’t reach far enough to grip the flashlight.

All of the sudden my head dipped down into the ash and my hand went around the flashlight. I was not able to breathe as my respirator (and my entire head) was entirely immersed in ash. Everything went dark. I struggled to get up, as Curtis had let go of my legs and I had plunged head first into the bottom of the hopper. I had one hand free as the other one held the flashlight. I used it to push against the opposite wall of the hopper to raise my head up out of the ash. I still couldn’t breathe as my respirator was now clogged solid with ash. When I tried to inhale, the respirator just gripped my face tighter. Finally with my one free hand pushing against the hopper wall to hold my head out of the ash, I reached up with the hand that held the flashlight and pushed against my respirator enough to break the seal around my face so that I was able to get a breath of air.

Then I quickly pulled myself out of the precipitator as I heard Curtis saying the mantra that I had heard one other time (as I indicated in the post about Power Plant Safety as Interpreted by Curtis Love). He was saying over and over again, “I’mSorry,I’mSorry, KevinI’mSorry, ThoseGuysWereTicklingMe. I’mSorry,IDidn’tMeanToLetGo,ITriedToHoldOn, butThoseGuysWereTicklingMe.”

Looking around I spied a few Labor Crew hands sneaking away. As this happened before when I was sandblasting in the sand filter tank when Curtis Love had turned off my air, this wasn’t the first encounter I had with Power Plant Men In-Training playing a Power Plant joke on me. I told Curtis to forget it. I had retrieved my flashlight and everything was all right. I was covered from head-to-toe with fly ash, but that washes off pretty easily.

It dawned on me then that when I had dropped the flashlight, it had sunk clear to the bottom of the hopper and down into the throat of the feeder at the bottom. If I had dived into the ash in the hopper from up above, I would have fallen right down to the bottom of the hopper and been engulfed in ash. My feet would have been pinned down in the feeder pipe, and that would have been the end of me. It probably would have taken many hours to figure out where I was, and they would have found only a corpse.

While I was hanging on the edge of the hopper with only the tip of my index finger gripping the ledge, I was actually considering letting go. There never would have been an electrician at the power Plant named Kevin Breazile. I never would have married my wife Kelly, and had my two children Elizabeth and Anthony. I would not be writing this story right now. If it had been left to my own stupidity, none of those things would have happened.

I believe it was my guardian angel that had talked me out of letting go (or had actually been standing on my finger). As stubborn as I was, and against my nature, that day I had decided to give up searching for my flashlight and seek help. That one momentary decision has made all the difference in my life.

Since that day I have had a certain appreciation for the things that happen to me even when they seem difficult at the time. I have lived a fairly stress-free life because each day is a gift. Currently I work in a stress-filled job where individual accomplishments are seldom rewarded. From one day to the next I may be laid off at any time. I still find a lot of satisfaction in what I do because it was possible that it never would have happened. I have been kept alive for a purpose so I might as well enjoy the ride.

I find a special love for the people I work with today, because they are all gifts to me. I try to pay them back with kindness… when that doesn’t work.. I try to annoy them with my presence… Just to say….. — I am still here!

Comments from previous repost:

  1. Dan Antion May 27, 2014

    Scary thought there at the end. Sounds like quick sand.

  2. Ron May 27, 2014

    I’m glad you chose to “give up” on going after a flashlight! There is a Proverb that says “There is a way which seems right to a man, but the end thereof is the way death.” Sounds like you found one of those “ways”. To choose to find your flashlight and lose your life would be the ultimate bad choice. God, give us the wisdom to choose the way of life.

  3. A.D. Everard August 4, 2014

    Wow. So close! You have a book with all these adventures, you really do. I’m enjoying reading these pages very much. I’m so glad you survived to write them!

  4. inmytwisteddreams August 17, 2014

    You are a very good story teller! I was drawn in from the first sentence, and engulfed in your words until the last. Great Story! I mean, not so great at the time, but glad you brought it full circle in the end! I always say, “You must never hesitate” – a simple statement, whose words most might take for granted. As humans, it’s typically against our nature to trust our first (or gut) instinct, but as you know, it is there for a reason! Good story! 🙂

    ~Nikki

Advertisements

Luxuries and Amenities of a Power Plant Labor Crew

Originally Posted on August 11, 2012.  Added a picture of Larry Riley:

When I was a janitor at the Power Plant there were times when we were christened by being allowed to work with the Labor Crew on jobs that needed to be done in a hurry.  Larry Riley was the foreman of the Labor Crew.  I had worked with Larry Riley during the summers when I was a summer help, and I always held him in high esteem.

I think he knew that, and he said he was glad to have me working for him whenever they were in a pinch to complete a job in a hurry.  I have described Larry as reminding me of the Marlboro Man, as he had a moustache that looked like his.

Yep. That’s the Marlboro Man

I finally found a picture of Larry taken a couple of decades later… Here he is:

Larry Riley 20 years after I first met him. He has a much newer hardhat in this picture

Larry Riley 20 years after I first met him. He has a much newer hardhat in this picture

The wonderful thing about working in a Power Plant is that when you drive through the gate in the morning, you never know what you might be doing that day.   Even after 20 years at the plant, I was still amazed by the diversity of jobs a person could do there.  Anyone who spent those 20 years actually working instead of doing a desk job, would know a lot about all kinds of equipment and instruments, and temperatures.

When I was young I was able to go to Minnesota to visit my cousins in a place called “Phelp’s Mill”.  Named after an old mill along a river that was a “self service” museum.  Across the road and on the hill loomed a big foreboding house where my cousins lived during the summers.  We would play hide-and-seek in that mill, which was mainly made out of wood.  It was 4 stories high if you include the basement and had a lot of places to hide.

Phelps Mill, MN where we played as a boy.  You can see the house on the hill in the background

This is a picture of the inside of Phelps Mill by Shawn Turner: http://www.flickr.com/photos/32364049@N04/7174048516/

When I began working in the Power Plant, I realized one day that this was like that old mill only on a much bigger scale.  You could spend half of a life time wandering around that plant before you actually knew where everything was.  Each day brought something new.  My first years as a summer help, most of the “emergencies” that I would take part in had to do with cleaning up coal.  When I was able to work with the Labor Crew, things became a lot more interesting.

One day in the spring of 1983 when I arrived at work ready to mop the floor and sweep and dust the Turbine Generators, I was told that I needed to get with Chuck Ross an A foreman over the Labor Crew at the time, because I was going to work with the Labor Crew that day.  I was told to bring my respirator… Which usually had meant it was time to shovel coal.  This day was different.

Chuck brought me to the Tool room and asked Bif Johnson to give me a new Rubber Mallet.

New Rubber Mallet just like this

I went with the labor crew up on #1 Boiler just above the Air Preheater Baskets that I didn’t know existed at the time…  The Boiler had been shutdown over night because there was a problem with the airflow through the boiler and we had to go in the duct and clean the Slag Screen.

Diagram of a boiler

Diagram of a boiler

Below the Economizer and above the air preheater in the diagram above.

“Slag Screen,” I thought… That sounds like a fancy word for something that was  probably just some kind of filter or something….  I knew that Power Plant Engineers liked to give fancy words to make the Plant sound more like a Palace.

As I mentioned before… there are places like:  The Tripper Gallery.  Hopper Nozzle Booster Pump. Generator Bathtub.  The Gravimetric Feeder Deck — I liked that one, it sounded like you were on a ship.  Travelling Water Screens.  There were long names for some, like “Force Draft Fan Inboard Bearing Emergency Lube Oil Pump” (try saying that with a lisp).  Anyway, I could go on and on.

Larry Riley explained to us that we needed to work as fast as we could to clean the slag screen because they wanted to bring this unit back online in the evening.  We couldn’t wait for the unit to cool down much, so we were only allowed to go in the hot air duct for 10 minutes at a time because of the heat.

So, in I went.  The first thing I noticed as I stuck my head in the door was that there wasn’t any immediate place to stand.  There was only a hole below me that went down into the darkness.  So I looked around for something to grab onto to pull myself in.  Once my body was in the door I was able to walk along a beam next to this big screen.  It looked similar to a screen on a window at home only the wires were about 1/2 inch apart.  Something like this:

A picture of a similar slag screen

Oh, and there was one more thing that I noticed…. It was incredibly HOT.  I was wearing leather gloves so I could grab onto the structure to hold myself up, but if I leaned against the screen with my arm, it would burn it.  I was just wearing a tee shirt.  I don’t know the exact temperature, but I have worked in similar heat at other times, and I would say that it was around 160 degrees.  I was not wearing my  hard hat because there was a strong wind blowing to try and cool the boiler down.

The problem is that we were on the tail end of the air flowing out of the boiler, and it was carrying all that heat right onto us.  At 160 degrees your hard hat will become soft so that you can squish it like a ball cap.  I was wearing Goggles as well, and that helped keep my eyes from drying out since everything else went dry the moment I stuck my head in there.

Anyway, I threw the lanyard for my safety belt around a pipe that ran diagonal across my path, and held onto it with one hand while with my other hand I began pounding on the screen with the rubber mallet.  I had to breathe very shallow because the air was so hot.  Breathing slowly gave the air time to cool off a bit before it went down into my throat.

This was a new adventure for me.  There are some Brave Power Plant Men that work on the “Bowl Mill” crew that have worked in these conditions for weeks at a time.  I suppose you grow used to it after a while.  Kind of like when you eat something with Habenero Sauce.  The first time it just very painful.  Then a few weeks later, you’re piling it on your tortilla chips.

After my first 10 minutes were over, someone at the door, (which was hard to see) hollered for me, so I made my way back to the door and emerged into the cool air of the morning.  I noticed that Larry Riley gave me a slightly worried look and I wondered what it meant.  I realized what it was moments later when I went to remove the respirator off of my face.  I only had one filter cartridge in the respirator.

Half-face respirator

The other one was missing.  I thought that was silly of me to go in there with only one filter.  No wonder it seemed like I was breathing a lot of dust.  Then I thought…. No.  I know I had both filters when I went in the duct.  I must have lost one while I was in there.  Maybe with all that banging I knocked it off.

Anyway, 10 minutes later it was time for me to go back in there, and this time I made sure my filters were securely screwed onto the respirator.  I worried in the back of my mind that I may have ruined my lungs for life by breathing all that silicon-based fly ash because I was feeling a little out of breathe (for the next 10 years).

Anyway, halfway through my 10 minutes in the duct I reached up with my hand to make sure my filters were still tightly screwed in place, and to my astonishment, they weren’t tight.  I tried tightening them, but I couldn’t screw them tight.  The respirator itself had become soft in the heat and the plastic was no longer stiff enough to keep the filter tight.  It made sense then why I had lost my filter the first time.  It must have fallen down into the abyss of darkness that was right behind me while I was banging on that slag screen.

After working on the screen for an hour or so, we took a break.  When we returned the temperature in the boiler had dropped considerably, and I was able to stay in the duct the rest of the day without having to climb in and out all the time.

Larry had an air powered needle gun brought up there and someone used that for a while cleaning the screen.  It is what it sounds like.  It has rods sticking out the end of a gun looking tool that vibrate wildly when you pull the trigger.  I don’t know what the real name is for it, but it cleaned slag screens a lot faster than my beating the screen with the rubber mallet all day.

Needle Gun

I did beat that screen all day.  When it was time to leave I brought the mallet back to the tool room, and it looked like this:

Rubber Mallet after banging on a slag screen all day

I had worn the rubber off of the  mallet.  When I brought the mallet back to the tool room, Bif said, “What is this?”  I said I was just returning the mallet that I had borrowed that morning.  He said something about how I must be some kind of a he-man or crazy.   I was too worried about my lungs to think about how much my wrists were aching from taking that pounding all day.

A couple of months later I was promoted to the Labor Crew.  Chuck Ross had kept saying that he couldn’t wait for me to go to the Labor Crew because he wanted me to work for him.  The very day that I started on the Labor Crew, the plant had a going-away party for Chuck Ross.  He was leaving our plant to go work at another one in Muskogee.

During the party Chuck presented me with the rubber mallet that I had used that day cleaning the slag screen.  He said he had never seen anything like that before.  He was sorry he was going to leave without having the opportunity to have me working for him.

I felt the same way about Chuck.  I have always kept that rubber mallet laying around the house since 1983 when I received it.  My wife sometimes picks it up when she is cleaning somewhere and says, “Do you still want this?” With a hopeful look, like someday I may say that it is all right if she throws it away.

Of course I want to keep it.  It reminds me of the days when I was able to work with True Power Plant Men in their natural environment.  The slag screen was later deemed unnecessary and was removed from the boiler.

It also reminds me of other things.  Like how quickly something can happen that changes your life forever.

Questions from that day have always remained with me.

How much ash did I breathe in?  I couldn’t see much more than a few feet in front of me as I banged on that screen knocking ash down all over me.  What did it do to my lungs?

What if I had taken a step back or slipped off of that beam before I had walked to the other end to secure my safety lanyard?  I know now what was below me then.  I would have fallen about 20 feet down to some fins, and then down another 20 feet onto the air preheater baskets.  It would have taken a while to retrieve me, once someone figured out that I was missing.

What does that much heat do to your body… or your brain?

I know these are things that go through the minds of True Power Plant Men.  I worked with them for years improving the safety of the power plant.  All-in-all, no one ever died when I was there, though some came close.  The Slogan over the Shift Supervisor’s Office said, “Safety is job #1”.  That wasn’t there to try to convince us that Safety was important.  It was there as a testimony to everyone who had already made that decision.

Comments from the previous repost:

  1. Jonathan Caswell August 12, 2014

    GLAD that you made it….even if the mallet didn’t!!!

    I can dig it. When I was hired for Security at one post…I really looked forward to working with and for that particular Supervisor who’d hired me. No such luck–she was gone in a month or two. THAT hurt! 🙂

  2. Ron Kilman August 13, 2014

    If the environment is too hot for a respirator to function properly in, it’s too hot for people to work in (if safety is actually job #1). I saw too many examples of “Get the Unit Back On is Job #1″.

 

Luxuries and Amenities of a Power Plant Labor Crew

Originally Posted on August 11, 2012.  Added a picture of Larry Riley:

When I was a janitor at the Power Plant there were times when we were christened by being allowed to work with the Labor Crew on jobs that needed to be done in a hurry.  Larry Riley was the foreman of the Labor Crew.  I had worked with Larry Riley during the summers when I was a summer help, and I always held him in high esteem.

I think he knew that, and he said he was glad to have me working for him whenever they were in a pinch to complete a job in a hurry.  I have described Larry as reminding me of the Marlboro Man, as he had a moustache that looked like his.

Yep. That’s the Marlboro Man

I finally found a picture of Larry taken a couple of decades later… Here he is:

Larry Riley 20 years after I first met him.  He has a much newer hardhat in this picture

Larry Riley 20 years after I first met him. He has a much newer hardhat in this picture

The wonderful thing about working in a Power Plant is that when you drive through the gate in the morning, you never know what you might be doing that day.   Even after 20 years at the plant, I was still amazed by the diversity of jobs a person could do there.  Anyone who spent those 20 years actually working instead of doing a desk job, would know a lot about all kinds of equipment and instruments, and temperatures.

When I was young I was able to go to Minnesota to visit my cousins in a place called “Phelp’s Mill”.  Named after an old mill along a river that was a “self service” museum.  Across the road and on the hill loomed a big foreboding house where my cousins lived during the summers.  We would play hide-and-seek in that mill, which was mainly made out of wood.  It was 4 stories high if you include the basement and had a lot of places to hide.

Phelps Mill, MN where we played as a boy.  You can see the house on the hill in the background

This is a picture of the inside of Phelps Mill by Shawn Turner: http://www.flickr.com/photos/32364049@N04/7174048516/

When I began working in the Power Plant, I realized one day that this was like that old mill only on a much bigger scale.  You could spend half of a life time wandering around that plant before you actually knew where everything was.  Each day brought something new.  My first years as a summer help, most of the “emergencies” that I would take part in had to do with cleaning up coal.  When I was able to work with the Labor Crew, things became a lot more interesting.

One day in the spring of 1983 when I arrived at work ready to mop the floor and sweep and dust the Turbine Generators, I was told that I needed to get with Chuck Ross an A foreman over the Labor Crew at the time, because I was going to work with the Labor Crew that day.  I was told to bring my respirator… Which usually had meant it was time to shovel coal.  This day was different.

Chuck brought me to the Tool room and asked Bif Johnson to give me a new Rubber Mallet.

New Rubber Mallet just like this

I went with the labor crew up on #1 Boiler just above the Air Preheater Baskets that I didn’t know existed at the time…  The Boiler had been shutdown over night because there was a problem with the airflow through the boiler and we had to go in the duct and clean the Slag Screen.

Diagram of a boiler

Diagram of a boiler

Below the Economizer and above the air preheater in the diagram above.

“Slag Screen,” I thought… That sounds like a fancy word for something that was  probably just some kind of filter or something….  I knew that Power Plant Engineers liked to give fancy words to make the Plant sound more like a Palace.

As I mentioned before… there are places like:  The Tripper Gallery.  Hopper Nozzle Booster Pump. Generator Bathtub.  The Gravimetric Feeder Deck — I liked that one, it sounded like you were on a ship.  Travelling Water Screens.  There were long names for some, like “Force Draft Fan Inboard Bearing Lube Oil Pump” (try saying that with a lisp).  Anyway, I could go on and on.

Larry Riley explained to us that we needed to work as fast as we could to clean the slag screen because they wanted to bring this unit back online in the evening.  We couldn’t wait for the unit to cool down much, so we were only allowed to go in the hot air duct for 10 minutes at a time because of the heat.

So, in I went.  The first thing I noticed as I stuck my head in the door was that there wasn’t any immediate place to stand.  There was only a hole below me that went down into the darkness.  So I looked around for something to grab onto to pull myself in.  Once my body was in the door I was able to walk along a beam next to this big screen.  It looked similar to a screen on a window at home only the wires were about 1/2 inch apart.  Something like this:

A picture of a similar slag screen

Oh, and there was one more thing that I noticed…. It was incredibly HOT.  I was wearing leather gloves so I could grab onto the structure to hold myself up, but if I leaned against the screen with my arm, it would burn it.  I was just wearing a tee shirt.  I don’t know the exact temperature, but I have worked in similar heat at other times, and I would say that it was around 150 degrees.  I was not wearing my  hard hat because there was a strong wind blowing to try and cool the boiler down.

The problem is that we were on the tail end of the air flowing out of the boiler, and it was carrying all that heat right onto us.  At 160 degrees your hard hat will become soft so that you can squish it like a ball cap.  I was wearing Goggles as well, and that helped keep my eyes from drying out since everything else went dry the moment I stuck my head in there.

Anyway, I threw the lanyard for my safety belt around a pipe that ran diagonal across my path, and held onto it with one hand while with my other hand I began pounding on the screen with the rubber mallet.  I had to breathe very shallow because the air was so hot.  Breathing slowly gave the air time to cool off a bit before it went down into my throat.

This was a new adventure for me.  There are some Brave Power Plant Men that work on the “Bowl Mill” crew that have worked in these conditions for weeks at a time.  I suppose you grow used to it after a while.  Kind of like when you eat something with Habenero Sauce.  The first time it just very painful.  Then a few weeks later, you’re piling it on your tortilla chips.

After my first 10 minutes were over, someone at the door, (which was hard to see) hollered for me, so I made my way back to the door and emerged into the cool air of the morning.  I noticed that Larry Riley gave me a slightly worried look and I wondered what it meant.  I realized what it was moments later when I went to remove the respirator off of my face.  I only had one filter cartridge in the respirator.

Half-face respirator

The other one was missing.  I thought that was silly of me to go in there with only one filter.  No wonder it seemed like I was breathing a lot of dust.  Then I thought…. No.  I know I had both filters when I went in the duct.  I must have lost one while I was in there.  Maybe with all that banging I knocked it off.

Anyway, 10 minutes later it was time for me to go back in there, and this time I made sure my filters were securely screwed onto the respirator.  I worried in the back of my mind that I may have ruined my lungs for life by breathing all that silicon-based fly ash because I was feeling a little out of breathe (for the next 10 years).

Anyway, halfway through my 10 minutes in the duct I reached up with my hand to make sure my filters were still tightly screwed in place, and to my astonishment, they weren’t tight.  I tried tightening them, but I couldn’t screw them tight.  The respirator itself had become soft in the heat and the plastic was no longer stiff enough to keep the filter tight.  It made sense then why I had lost my filter the first time.  It must have fallen down into the abyss of darkness that was right behind me while I was banging on that slag screen.

After working on the screen for an hour or so, we took a break.  When we returned the temperature in the boiler had dropped considerably, and I was able to stay in the duct the rest of the day without having to climb in and out all the time.

Larry had an air powered needle gun brought up there and someone used that for a while cleaning the screen.  It is what it sounds like.  It has rods sticking out the end of a gun looking tool that vibrate wildly when you pull the trigger.  I don’t know what the real name is for it, but it cleaned slag screens a lot faster than my beating the screen with the rubber mallet all day.

Needle Gun

I did beat that screen all day.  When it was time to leave I brought the mallet back to the tool room, and it looked like this:

Rubber Mallet after banging on a slag screen all day

I had worn the rubber off of the  mallet.  When I brought the mallet back to the tool room, Bif said, “What is this?”  I said I was just returning the mallet that I had borrowed that morning.  He said something about how I must be some kind of a he-man or crazy.   I was too worried about my lungs to think about how much my wrists were aching from taking that pounding all day.

A couple of months later I was promoted to the Labor Crew.  Chuck Ross had kept saying that he couldn’t wait for me to go to the Labor Crew because he wanted me to work for him.  The very day that I started on the Labor Crew, the plant had a going-away party for Chuck Ross.  He was leaving our plant to go work at another one in Muskogee.

During the party Chuck presented me with the rubber mallet that I had used that day cleaning the slag screen.  He said he had never seen anything like that before.  He was sorry he was going to leave without having the opportunity to have me working for him.

I felt the same way about Chuck.  I have always kept that rubber mallet laying around the house since 1983 when I received it.  My wife sometimes picks it up when she is cleaning somewhere and says, “Do you still want this?” With a hopeful look, like someday I may say that it is all right if she throws it away.

Of course I want to keep it.  It reminds me of the days when I was able to work with True Power Plant Men in their natural environment.  The slag screen was later deemed unnecessary and was removed from the boiler.

It also reminds me of other things.  Like how quickly something can happen that changes your life forever.

Questions from that day have always remained with me.

How much ash did I breathe in?  I couldn’t see much more than a few feet in front of me as I banged on that screen knocking ash down all over me.  What did it do to my lungs?

What if I had taken a step back or slipped off of that beam before I had walked to the other end to secure my safety lanyard?  I know now what was below me then.  I would have fallen about 20 feet down to some fins, and then down another 20 feet onto the air preheater baskets.  It would have taken a while to retrieve me, once someone figured out that I was missing.

What does that much heat do to your body… or your brain?

I know these are things that go through the minds of True Power Plant Men.  I worked with them for years improving the safety of the power plant.  All-in-all, no one ever died when I was there, though some came close.  The Slogan over the Shift Supervisor’s Office said, “Safety is job #1”.  That wasn’t there to try to convince us that Safety was important.  It was there as a testimony to everyone who had already made that decision.

Comments from the previous repost:

  1. Jonathan Caswell August 12, 2014

    GLAD that you made it….even if the mallet didn’t!!!

    I can dig it. When I was hired for Security at one post…I really looked forward to working with and for that particular Supervisor who’d hired me. No such luck–she was gone in a month or two. THAT hurt! 🙂

  2. Ron Kilman August 13, 2014

    If the environment is too hot for a respirator to function properly in, it’s too hot for people to work in (if safety is actually job #1). I saw too many examples of “Get the Unit Back On is Job #1″.

 

Angel of Death Passes by the Precipitator Door

Originally published on May 25, 2012:

Either this was the luckiest day of my life, or a day where stupidity seemed to be my natural state of mind. This particular day occurred sometime in September 1983. The Main Power transformer for Unit 1 had  shutdown because of an internal fault during an exceptionally hot day during the summer and was being replaced. While the unit was offline, while I was on the labor crew, I was asked to help out the electricians who were doing an overhaul on the Precipitator. The Precipitator takes the ash out of the boiler exhaust before it goes up the smoke stack. Without it, you would see thick smoke, instead, you see only clear exhaust. At the time the electricians I worked with were Sonny Kendrick and Bill Rivers. I had already applied for a job in the electric shop and was waiting to see if I was going to be offered the job. This gave me the chance to show the electricians what a brilliant worker I was.

Bill Rivers told me to go in the precipitator and wipe down the insulators that held the wire racks in place. He showed me where they were. I wore a regular half-face respirator because the fly ash is harmful to inhale.

Half-face respirator

Just before I went in the precipitator door to begin wiping down the insulators using a Scotch Brite Pad, Bill Rivers pointed to my flashlight and said, “Don’t drop your flashlight in a hopper otherwise you will have to make sure that you get it out of the hopper before we go back online.” I told him I would be sure to hold onto my flashlight (noticing that Bill had a string tied to his flashlight which was slung over his shoulder) and I entered the precipitator door.

Yellow Flashlight similar to the one I carried

The inside of the precipitator was dark. 70 foot tall plates are lined up 9 inches apart. Wires hang down between the plates and when the precipitator is turned on, the wires are charged up to around 45,000 volts of electricity. The wires each have a 30 pound weight on the bottom to keep the wires straight, and the wires are kept apart and lined up by a rack at the bottom. One end of the rack which is about 25 feet long is held in place by an electrical insulator about 3 feet long. This is what I was supposed to clean. The light from the flashlight lit up the area around me because everything was covered with the fine white powder reflecting the light.

The first hopper I came to was full of ash up to the top of the hopper, but just below where the insulator was mounted to the edge of the hopper. So, I worked my way down to the ledge along the edge of the hopper and dangled my feet down into the ash as I prepared to wipe down the first of the four insulators on this particular hopper. Just as I began, the precipitator suddenly went dark as my flashlight fell from my hand and down into the hopper. — Oh boy, that didn’t take long.

Fly Ash Hoppers. Our hoppers were 12 foot by 12 foot at the top.

I sat there for a minute in the dark as my eyes grew accustomed to the small amount of light that was coming through the doors. After I could see again, I reached my hand into the ash to feel for my flashlight. The ash was very fluffy and there was little or no resistance as I flailed my hand around searching for it. I leaned over farther and farther to reach down deeper into the ash. I was at the point where I was laying down flat on the ledge trying to find the flashlight, and it was no where to be found.

I pulled myself over to the side edge of the hopper and dropped myself down into the ash so that I could reach over where I had dropped the light, but I was still not able to find it. At that point, I was leaning out into the hopper with only my one index finger gripping the ledge around the hopper. I had a decision to make… I thought I would just bail off into the ash to see if I could find the flashlight, or I could give up and go tell Bill Rivers that I had done the one thing that he told me not to do, and in record time.

I don’t usually like to give up until I have exhausted every effort, so here was my dilemma. Do I let go and dive into this ash to retrieve my flashlight? Or do I leave the hopper and go tell Bill? I regretfully decided to go tell Bill. So, I climbed up out of the hopper, with my clothes covered with Ash (as we did not have fly ash suits at the time and I was wearing my coveralls). I made my way to the precipitator door and once I was outside, I determined which hopper I had been in when I dropped my flashlight.

I found Bill and told him that I had dropped my flashlight in a hopper full of ash. He told me to get the key for that hopper and open the door at the bottom and see if I could find the flashlight. Unlike the picture of the hoppers above, we had a landing around the base of the hoppers by the access door so you didn’t need a ladder to reach them.

Curtis Love had been watching the door of the precipitator for me while I was supposed to be wiping off the insulators. He came down with me, and we proceeded to open the access door at the bottom on the side of the hopper. When I opened the door both Curtis and I were swept backward as a stream of fly ash shot from the door. The ash fell through the grating to the ground below. We regained our footing and watched as a tremendous pile of ash grew below us. If the flashlight had come out of the doorway, it would have remained on the landing since it was too big to go through the grating, but it never came out.

After the ash had finished pouring out of the hopper as if it were water, I reached down into the remaining ash to see if I could feel the flashlight. Still I was unable to find it. There was about 4 more feet from the doorway to the bottom of the hopper, so I emptied out as much ash as I could using my hard hat for a shovel. Then I pulled my body head first into the hopper and I reached down as far as I could in the bottom of the hopper, but I couldn’t find the flashlight.

So, in my infinite wisdom, I asked Curtis Love to hold onto my legs as I lowered myself down to the throat at the bottom of the hopper. I lowered myself down until I had half of my face laying in the ash. At this point only one of the two filters on my respirator was able to function as the other one was down in the ash. I reached my hand into the top of the feeder at the bottom of the hopper and with my finger tips I could just feel the flashlight. I had reached as far as I could, but I couldn’t reach far enough to grip the flashlight.

All of the sudden my head dipped down into the ash and my hand went around the flashlight. I was not able to breathe as my respirator (and my entire head) was entirely immersed in ash. Everything went dark. I struggled to get up, as Curtis had let go of my legs and I had plunged head first into the bottom of the hopper. I had one hand free as the other one held the flashlight. I used it to push against the opposite wall of the hopper to raise my head up out of the ash. I still couldn’t breathe as my respirator was now clogged solid with ash. When I tried to inhale, the respirator just gripped my face tighter. Finally with my one free hand pushing against the hopper wall to hold my head out of the ash, I reached up with the hand that held the flashlight and pushed against my respirator enough to break the seal around my face so that I was able to get a breath of air.

Then I quickly pulled myself out of the precipitator as I heard Curtis saying the mantra that I had heard one other time (as I indicated in the post about Power Plant Safety as Interpreted by Curtis Love). He was saying over and over again, “I’mSorry,I’mSorry, KevinI’mSorry, ThoseGuysWereTicklingMe. I’mSorry,IDidn’tMeanToLetGo,ITriedToHoldOn, butThoseGuysWereTicklingMe.”

Looking around I spied a few Labor Crew hands sneaking away. As this happened before when I was sandblasting in the sand filter tank when Curtis Love had turned off my air, this wasn’t the first encounter I had with Power Plant Men In-Training playing a Power Plant joke on me. I told Curtis to forget it. I had retrieved my flashlight and everything was all right. I was covered from head-to-toe with fly ash, but that washes off pretty easily.

It dawned on me then that when I had dropped the flashlight, it had sunk clear to the bottom of the hopper and down into the throat of the feeder at the bottom. If I had dived into the ash in the hopper from up above, I would have fallen right down to the bottom of the hopper and been engulfed in ash. My feet would have been pinned down in the feeder pipe, and that would have been the end of me. It probably would have taken many hours to figure out where I was, and they would have found only a corpse.

While I was hanging on the edge of the hopper with only the tip of my index finger gripping the ledge, I was actually considering letting go. There never would have been an electrician at the power Plant named Kevin Breazile. I never would have married my wife Kelly, and had my two children Elizabeth and Anthony. I would not be writing this story right now. If it had been left to my own stupidity, none of those things would have happened. I believe it was my guardian angel that had talked me out of letting go (or had actually been standing on my fingers). As stubborn as I was, and against my nature, that day I had decided to give up searching for my flashlight and seek help. That one momentary decision has made all the difference in my life.

Since that day I have had a certain appreciation for the things that happen to me even when they seem difficult at the time. I have lived a fairly stress-free life because each day is a gift. Currently I work in a stress-filled job where individual accomplishments are seldom rewarded. From one day to the next I may be laid off at any time. I still find a lot of satisfaction in what I do because it was possible that it never would have happened. I have been kept alive for a purpose so I might as well enjoy the ride.

I find a special love for the people I work with today, because they are all gifts to me. I try to pay them back with kindness… when that doesn’t work.. I try to annoy them with my presence… Just to say….. — I am still here!

Comments from previous repost:

  1. Dan Antion May 27, 2014

    Scary thought there at the end. Sounds like quick sand.

  2. Ron May 27, 2014

    I’m glad you chose to “give up” on going after a flashlight! There is a Proverb that says “There is a way which seems right to a man, but the end thereof is the way death.” Sounds like you found one of those “ways”. To choose to find your flashlight and lose your life would be the ultimate bad choice. God, give us the wisdom to choose the way of life.

  3. A.D. Everard August 4, 2014

    Wow. So close! You have a book with all these adventures, you really do. I’m enjoying reading these pages very much. I’m so glad you survived to write them!

  4. inmytwisteddreams August 17, 2014

    You are a very good story teller! I was drawn in from the first sentence, and engulfed in your words until the last. Great Story! I mean, not so great at the time, but glad you brought it full circle in the end! I always say, “You must never hesitate” – a simple statement, whose words most might take for granted. As humans, it’s typically against our nature to trust our first (or gut) instinct, but as you know, it is there for a reason! Good story! 🙂

    ~Nikki

Luxuries and Amenities of a Power Plant Labor Crew — Repost

Originally Posted on August 11, 2012.  Added a picture of Larry Riley:

When I was a janitor at the Power Plant there were times when we were christened by being allowed to work with the Labor Crew on jobs that needed to be done in a hurry.  Larry Riley was the foreman of the Labor Crew.  I had worked with Larry Riley during the summers when I was a summer help, and I always held him in high esteem.  I think he knew that, and he said he was glad to have me working for him whenever they were in a pinch to complete a job in a hurry.  I have described Larry as reminding me of the Marlboro Man, as he had a moustache that looked like his.

Yep. That’s the Marlboro Man

I finally found a picture of Larry taken a couple of decades later… Here he is:

Larry Riley 20 years after I first met him.  He has a much newer hardhat in this picture

Larry Riley 20 years after I first met him. He has a much newer hardhat in this picture

The wonderful thing about working in a Power Plant is that when you drive through the gate in the morning, you never know what you might be doing that day.   Even after 20 years at the plant, I was still amazed by the diversity of jobs a person could do there.  Anyone who spent those 20 years actually working instead of doing a desk job, would know a lot about all kinds of equipment and instruments, and temperatures.

When I was young I was able to go to Minnesota to visit my cousins in a place called “Phelp’s Mill”.  Named after an old mill along a river that was a “self service” museum.  Across the road and on the hill loomed a big foreboding house where my cousins lived during the summers.  We would play hide-and-seek in that mill, which was mainly made out of wood.  It was 4 stories high if you include the basement and had a lot of places to hide.

Phelps Mill, MN where we played as a boy.  You can see the house on the hill in the background

This is a picture of the inside of Phelps Mill by Shawn Turner: http://www.flickr.com/photos/32364049@N04/7174048516/

When I began working in the Power Plant, I realized one day that this was like that old mill only on a much bigger scale.  You could spend half of a live time wandering around that plant before you actually knew where everything was.  So, each day brought something new.  My first years as a summer help, most of the “emergencies” that I would take part in had to do with cleaning up coal.  When I was able to work with the Labor Crew, things became a lot more interesting.

One day in the spring of 1983 when I arrived at work ready to mop the floor and sweep and dust the Turbine Generators, I was told that I needed to get with Chuck Ross an A foreman over the Labor Crew at the time, because I was going to work with the Labor Crew that day.  I was told to bring my respirator… Which usually had meant it was time to shovel coal.  This day was different.

Chuck brought me to the Tool room and asked Bif Johnson to give me a new Rubber Mallet.

New Rubber Mallet just like this

I went with the labor crew up on #1 Boiler just above the Air Preheater Baskets that I didn’t know existed at the time…  The Boiler had been shutdown over night because there was a problem with the airflow through the boiler and we had to go in the duct and clean the Slag Screen.

“Slag Screen,” I thought… That sounds like a fancy word for something that was  probably just some kind of filter or something….  I knew that Power Plant Engineers liked to give fancy words to make the Plant sound more like a Palace.  As I mentioned before… there are places like:  The Tripper Gallery.  Hopper Nozzle Booster Pump. Generator Bathtub.  The Gravimetric Feeder Deck — I liked that one, it sounded like you were on a ship.  Travelling Water Screens.  There were long names for some, like “Force Draft Fan Inboard Bearing Lube Oil Pump” (try saying that with a lisp).  Anyway, I could go on and on.

Larry Riley explained to us that we needed to work as fast as we could to clean the slag screen because they wanted to bring this unit back on in the evening.  We couldn’t wait for the unit to cool down much, so we were only allowed to go in the hot air duct for 10 minutes at a time.

So, in I went.  The first thing I noticed as I stuck my head in the door was that there wasn’t any immediate place to stand.  There was only a hole below me that went down into the darkness.  So I looked around for something to grab onto to pull myself in.  Once my body was in the door I was able to walk along a beam next to this big screen.  It looked similar to a screen on a window at home only the wires were about 1/2 inch apart.  Something like this:

A picture of a similar slag screen

Oh, and there was one more thing that I noticed…. It was incredibly HOT.  I was wearing leather gloves so I could grab onto the structure to hold myself up, but if I leaned against the screen with my arm, it would burn it.  I was just wearing a t-shirt.  I don’t know the exact temperature, but I have worked in similar heat at other times, and I would say that it was around 150 degrees.  I was not wearing my  hard hat because there was a strong wind blowing to try and cool the boiler down.

The problem is that we were on the tail end of the air flowing out of the boiler, and it was carrying all that heat right onto us.  At 160 degrees your hard hat will become soft so that you can squish it like a ball cap.  I was wearing Goggles as well, and that helped keep my eyes from drying out since everything else went dry the moment I stuck my head in there.

Anyway, I threw my lanyard around a pipe that ran diagonal across my path, and held onto it with one hand while with my other hand I began pounding on the screen with the rubber mallet.  I had to breathe very shallow because the air was so hot.  It gave the air time to cool off a bit before it went down into my throat.

This was a new adventure for me.  There are some Brave Power Plant Men that work on the “Bowl Mill” crew that have worked in these conditions for weeks at a time.  I suppose you grow used to it after a while.  Kind of like when you eat something with Habenero Sauce.  The first time it just very painful.  Then a few weeks later, you’re piling it on your tortilla chips.

After my first 10 minutes were over, someone at the door, (which was hard to see) hollered for me, so I made my way back to the door and emerged into the cool air of the morning.  I noticed that Larry Riley gave me a slightly worried look and I wondered what it meant.  I realized what it was moments later when I went to remove the respirator off of my face.  I only had one filter cartridge in the respirator.

Half-face respirator

The other one was missing.  I thought that was silly of me to go in there with only one filter.  No wonder it seemed like I was breathing a lot of dust.  Then I thought…. No.  I know I had both filters when I went in the duct.  I must have lost one while I was in there.  Maybe with all that banging I knocked it off.

Anyway, 10 minutes later it was time for me to go back in there, and this time I made sure my filters were securely screwed onto the respirator.  I worried in the back of my mind that I may have ruined my lungs for life by breathing all that silicon based fly ash because I was feeling a little out of breathe (for the next 10 years).

Anyway, halfway through my 10 minutes in the duct I reached up with my hand to make sure my filters were still tightly screwed in place, and to my astonishment, they weren’t tight.  I couldn’t screw them tight.  The respirator itself had become soft in the heat and the plastic was no longer stiff enough to keep the filter tight.  It made sense then why I had lost my filter the first time.  It must have fallen down into the abyss of darkness that was right behind me while I was banging on that slag screen.

After working on the screen for an hour or so, we took a break.  When we returned the temperature in the boiler had dropped considerably, and I was able to stay in the duct the rest of the day without having to climb in and out all the time.

Larry had an air powered needle gun brought up there and someone used that for a while cleaning the screen.  It is what it sounds like.  It has rods sticking out the end of a gun looking tool that vibrate wildly when you pull the trigger.  I don’t know what the real name is for it, but it cleaned slag screens a lot faster than my beating the screen with the rubber mallet all day.

Needle Gun

I did beat that screen all day.  When it was time to leave I brought the mallet back to the tool room, and it looked like this:

Rubber Mallet after banging on a slag screen all day

I had worn the rubber off of the  mallet.  When I brought the mallet back to the tool room, Bif said, “What is this?”  I said I was just returning the mallet that I had borrowed that morning.  He said something about how I must be some kind of a he-man or crazy.   I was too worried about my lungs to think about how much my wrists were aching from taking that pounding all day.

A couple of months later I was promoted to the Labor Crew.  Chuck Ross had kept saying that he couldn’t wait for me to go to the Labor Crew because he wanted me to work for him.  The very day that I started on the Labor Crew, the plant had a going-away party for Chuck Ross.  He was leaving our plant to go work at another one in Muskogee.

During the party Chuck presented me with the rubber mallet that I had used that day cleaning the slag screen.  He said he had never seen anything like that before.  He was sorry he was going to leave without having the opportunity to have me working for him.  I felt the same way about Chuck.  I have always kept that rubber mallet laying around the house since 1983 when I received it.  My wife sometimes picks it up when she is cleaning somewhere and says, “Do you still want this?” With a hopeful look, like someday I may say that it is all right if she throws it away.

Of course I want to keep it.  It reminds me of the days when I was able to work with True Power Plant Men in their natural environment.  The slag screen was later deemed unnecessary and was removed from the boiler.

It also reminds me of other things.  Like how quickly something can happen that changes your life forever.

Questions from that day have always remained with me.

How much ash did I breathe in?  I couldn’t see much more than a few feet in front of me as I banged on that screen knocking ash down all over me.  What did it do to my lungs?

What if I had taken a step back or slipped off of that beam before I had walked to the other end to secure my safety lanyard?  I know now what was below me then.  I would have fallen about 20 feet down to some fins, and then down another 20 feet onto the air preheater baskets.  It would have taken a while to retrieve me, once someone figured out that I was missing.

What does that much heat do to your body… or your brain?

I know these are things that go through the minds of True Power Plant Men.  I worked with them for years improving the safety of the power plant.  All-in-all, no one ever died when I was there, though some came close.  The Slogan over the Shift Supervisor’s Office said, “Safety is job #1”.  That wasn’t there to try to convince us that Safety was important.  It was there as a testimony to everyone who had already made that decision.

Angel of Death Passes by the Precipitator Door — Repost

Originally published on May 25, 2012:

Either this was the luckiest day of my life, or a day where stupidity seemed to be my natural state of mind. This particular day occurred sometime in September 1983. The Main Power transformer for Unit 1 had  shutdown because of an internal fault during an exceptionally hot day during the summer and was being replaced. While the unit was offline, while I was on the labor crew, I was asked to help out the electricians who were doing an overhaul on the Precipitator. The Precipitator takes the ash out of the boiler exhaust before it goes up the smoke stack. Without it, you would see thick smoke, instead, you see only clear exhaust. At the time the electricians I worked with were Sonny Kendrick and Bill Rivers. I had already applied for a job in the electric shop and was waiting to see if I was going to be offered the job. This gave me the chance to show the electricians what a brilliant worker I was.

Bill Rivers told me to go in the precipitator and wipe down the insulators that held the wire racks in place. He showed me where they were. I wore a regular half-face respirator because the fly ash is harmful to inhale.

Half-face respirator

Just before I went in the precipitator door to begin wiping down the insulators using a Scotch Brite Pad, Bill Rivers pointed to my flashlight and said, “Don’t drop your flashlight in a hopper otherwise you will have to make sure that you get it out of the hopper before we go back online.” I told him I would be sure to hold onto my flashlight (noticing that Bill had a string tied to his flashlight which was slung over his shoulder) and I entered the precipitator door.

Yellow Flashlight similar to the one I carried

The inside of the precipitator was dark. 70 foot tall plates are lined up 9 inches apart. Wires hang down between the plates and when the precipitator is turned on, the wires are charged up to around 45,000 volts of electricity. The wires each have a 30 pound weight on the bottom to take out the tension, and the wires are kept apart and lined up by a rack at the bottom. One end of the rack which is about 25 feet long is held in place by an electrical insulator about 3 feet long. This is what I was supposed to clean. The light from the flashlight lit up the area around me because everything was covered with the fine white powder reflecting the light.

The first hopper I came to was full of ash up to the top of the hopper, but just below where the insulator was mounted to the edge of the hopper. So, I worked my way down to the ledge along the edge of the hopper and dangled my feet down into the ash as I prepared to wipe down the first of the four insulators on this particular hopper. Just as I began, the precipitator suddenly went dark as my flashlight fell from my hand and down into the hopper. — Oh boy, that didn’t take long.

Fly Ash Hoppers. Our hoppers were 12 foot by 12 foot at the top.

I sat there for a minute in the dark as my eyes grew accustomed to the small amount of light that was coming through the doors. After I could see again, I reached my hand into the ash to feel for my flashlight. The ash was very fluffy and there was little or no resistance as I flailed my hand around searching for it. I leaned over farther and farther to reach down deeper into the ash. I was at the point where I was laying down flat on the ledge trying to find the flashlight, and it was no where to be found.

I pulled myself over to the side edge of the hopper and dropped myself down into the ash so that I could reach over where I had dropped the light, but I was still not able to find it. At that point, I was leaning out into the hopper with only my one index finger gripping the ledge around the hopper. I had a decision to make… I thought I would just bail off into the ash to see if I could find the flashlight, or I could give up and go tell Bill Rivers that I had done the one thing that he told me not to do, and in record time. I don’t usually like to give up until I have exhausted every effort, so here was my dilemma. Do I let go and dive into this ash to retrieve my flashlight? Or do I leave the hopper and go tell Bill? I regretfully decided to go tell Bill. So, I climbed up out of the hopper, with my clothes covered with Ash (as we did not have fly ash suits at the time and I was wearing my coveralls). I made my way to the precipitator door and once I was outside, I determined which hopper I had been in when I dropped my flashlight.

I found Bill and told him that I had dropped my flashlight in a hopper full of ash. He told me to get the key for that hopper and open the door at the bottom and see if I could find the flashlight. Unlike the picture of the hoppers above, we had a landing around the base of the hoppers by the access door so you didn’t need a ladder to reach them.

Curtis Love had been watching the door of the precipitator for me while I was supposed to be wiping off the insulators. He came down with me, and we proceeded to open the access door at the bottom on the side of the hopper. When I opened the door both Curtis and I were swept backward as a stream of fly ash shot from the door. The ash fell through the grating to the ground below. We regained our footing and watched as a tremendous pile of ash grew below us. If the flashlight had come out of the doorway, it would have remained on the landing since it was too big to go through the grating, but it never came out.

After the ash had finished pouring out of the hopper as if it were water, I reached down into the remaining ash to see if I could feel the flashlight. Still I was unable to find it. There was about 4 more feet from the doorway to the bottom of the hopper, so I emptied out as much ash as I could using my hard hat for a shovel. Then I pulled my body head first into the hopper and I reached down as far as I could in the bottom of the hopper, but I couldn’t find the flashlight.

So, in my infinite wisdom, I asked Curtis Love to hold onto my legs as I lowered myself down to the throat at the bottom of the hopper. I lowered myself down until I had half of my face laying in the ash. At this point only one of the two filters on my respirator was able to function as the other one was down in the ash. I reached my hand into the top of the feeder at the bottom of the hopper and with my finger tips I could just feel the flashlight. I had reached as far as I could, but I couldn’t reach far enough to grip the flashlight.

All of the sudden my head dipped down into the ash and my hand went around the flashlight. I was not able to breathe as my respirator (and my entire head) was entirely immersed in ash. Everything went dark. I struggled to get up, as Curtis had let go of my legs and I had plunged head first into the bottom of the hopper. I had one hand free as the other one held the flashlight. I used it to push against the opposite wall of the hopper to raise my head up out of the ash. I still couldn’t breathe as my respirator was now clogged solid with ash. When I tried to inhale, the respirator just gripped my face tighter. Finally with my one free hand pushing against the hopper wall to hold my head out of the ash, I reached up with the hand that held the flashlight and pushed against my respirator enough to break the seal around my face so that I was able to get a breath of air.

Then I quickly pulled myself out of the precipitator as I heard Curtis saying the mantra that I had heard one other time (as I indicated in the post about Power Plant Safety as Interpreted by Curtis Love). He was saying over and over again, “I’mSorry,I’mSorry, KevinI’mSorry, ThoseGuysWereTicklingMe. I’mSorry,IDidn’tMeanToLetGo,ITriedToHoldOn, butThoseGuysWereTicklingMe.”

Looking around I spied a few Labor Crew hands sneaking away. As this happened before when I was sandblasting in the sand filter tank when Curtis Love had turned off my air, this wasn’t the first encounter I had with Power Plant Men In-Training playing a Power Plant joke on me. I told Curtis to forget it. I had retrieved my flashlight and everything was all right. I was covered from head-to-toe with fly ash, but that washes off pretty easily.

It dawned on me then that when I had dropped the flashlight, it had sunk clear to the bottom of the hopper and down into the throat of the feeder at the bottom. If I had dived into the ash in the hopper from up above, I would have fallen right down to the bottom of the hopper and been engulfed in ash. My feet would have been pinned down in the feeder pipe, and that would have been the end of me. It probably would have taken many hours to figure out where I was, and they would have found only a corpse.

While I was hanging on the edge of the hopper with only the tip of my index finger gripping the ledge, I was actually considering letting go. There never would have been an electrician at the power Plant named Kevin Breazile. I never would have married my wife Kelly, and had my two children Elizabeth and Anthony. I would not be writing this story right now. If it had been left to my own stupidity, none of those things would have happened. I believe it was my guardian angel that had talked me out of letting go (or had actually been standing on my fingers). As stubborn as I was, and against my nature, that day I had decided to give up searching for my flashlight and seek help. That one momentary decision has made all the difference in my life.

Since that day I have had a certain appreciation for the things that happen to me even when they seem difficult at the time. I have lived a fairly stress-free life because each day is a gift. Currently I work in a stress-filled job where individual accomplishments are seldom rewarded. From one day to the next I may be laid off at any time. I still find a lot of satisfaction in what I do because it was possible that it never would have happened. I have been kept alive for a purpose so I might as well enjoy the ride.

I find a special love for the people I work with today, because they are all gifts to me. I try to pay them back with kindness… when that doesn’t work.. I try to annoy them with my presence… Just to say….. — I am still here!

Luxuries and Amenities of a Power Plant Labor Crew — Repost

Originally Posted on August 11, 2012:

When I was a janitor at the Power Plant there were times when we were christened by being allowed to work with the Labor Crew on jobs that needed to be done in a hurry.  Larry Riley was the foreman of the Labor Crew.  I had worked with Larry Riley during the summers when I was a summer help, and I always held him in high esteem.  I think he knew that, and he said he was glad to have me working for him whenever they were in a pinch to complete a job in a hurry.  I have described Larry as reminding me of the Marlboro Man, as he had a moustache that looked like his.

Yep. That’s the Marlboro Man

The wonderful thing about working in a Power Plant is that when you drive through the gate in the morning, you never know what you might be doing that day.   Even after 20 years at the plant, I was still amazed by the diversity of jobs a person could do there.  Anyone who spent those 20 years actually working instead of doing a desk job, would know a lot about all kinds of equipment and instruments, and temperatures.

When I was young I was able to go to Minnesota to visit my cousins in a place called “Phelp’s Mill”.  Named after an old mill along a river that was a “self service” museum.  Across the road and on the hill loomed a big foreboding house where my cousins lived during the summers.  We would play hide-and-seek in that mill, which was mainly made out of wood.  It was 4 stories high if you include the basement and had a lot of places to hide.

Phelps Mill, MN where we played as a boy.  You can see the house on the hill in the background

This is a picture of the inside of Phelps Mill by Shawn Turner: http://www.flickr.com/photos/32364049@N04/7174048516/

When I began working in the Power Plant, I realized one day that this was like that old mill only on a much bigger scale.  You could spend half of a live time wandering around that plant before you actually knew where everything was.  So, each day brought something new.  My first years as a summer help, most of the “emergencies” that I would take part in had to do with cleaning up coal.  When I was able to work with the Labor Crew, things became a lot more interesting.

One day in the spring of 1983 when I arrived at work ready to mop the floor and sweep and dust the Turbine Generators, I was told that I needed to get with Chuck Ross an A foreman over the Labor Crew at the time, because I was going to work with the Labor Crew that day.  I was told to bring my respirator… Which usually had meant it was time to shovel coal.  This day was different.

Chuck brought me to the Tool room and asked Bif Johnson to give me a new Rubber Mallet.

New Rubber Mallet just like this

I went with the labor crew up on #1 Boiler just above the Air Preheater Baskets that I didn’t know existed at the time…  The Boiler had been shutdown over night because there was a problem with the airflow through the boiler and we had to go in the duct and clean the Slag Screen.

“Slag Screen,” I thought… That sounds like a fancy word for something that was  probably just some kind of filter or something….  I knew that Power Plant Engineers liked to give fancy words to make the Plant sound more like a Palace.  As I mentioned before… there are places like:  The Tripper Gallery.  Hopper Nozzle Booster Pump. Generator Bathtub.  The Gravimetric Feeder Deck — I liked that one, it sounded like you were on a ship.  Travelling Water Screens.  There were long names for some, like “Force Draft Fan Inboard Bearing Lube Oil Pump” (try saying that with a lisp).  Anyway, I could go on and on.

Larry Riley explained to us that we needed to work as fast as we could to clean the slag screen because they wanted to bring this unit back on in the evening.  We couldn’t wait for the unit to cool down much, so we were only allowed to go in the hot air duct for 10 minutes at a time.

So, in I went.  The first thing I noticed as I stuck my head in the door was that there wasn’t any immediate place to stand.  There was only a hole below me that went down into the darkness.  So I looked around for something to grab onto to pull myself in.  Once my body was in the door I was able to walk along a beam next to this big screen.  It looked similar to a screen on a window at home only the wires were about 1/2 inch apart.  Something like this:

A picture of a similar slag screen

Oh, and there was one more thing that I noticed…. It was incredibly HOT.  I was wearing leather gloves so I could grab onto the structure to hold myself up, but if I leaned against the screen with my arm, it would burn it.  I was just wearing a t-shirt.  I don’t know the exact temperature, but I have worked in similar heat at other times, and I would say that it was around 150 degrees.  I was not wearing my  hard hat because there was a strong wind blowing to try and cool the boiler down.

The problem is that we were on the tail end of the air flowing out of the boiler, and it was carrying all that heat right onto us.  At 160 degrees your hard hat will become soft so that you can squish it like a ball cap.  I was wearing Goggles as well, and that helped keep my eyes from drying out since everything else went dry the moment I stuck my head in there.

Anyway, I threw my lanyard around a pipe that ran diagonal across my path, and held onto it with one hand while with my other hand I began pounding on the screen with the rubber mallet.  I had to breathe very shallow because the air was so hot.  It gave the air time to cool off a bit before it went down into my throat.

This was a new adventure for me.  There are some Brave Power Plant Men that work on the “Bowl Mill” crew that have worked in these conditions for weeks at a time.  I suppose you grow used to it after a while.  Kind of like when you eat something with Habenero Sauce.  The first time it just very painful.  Then a few weeks later, you’re piling it on your tortilla chips.

After my first 10 minutes were over, someone at the door, (which was hard to see) hollered for me, so I made my way back to the door and emerged into the cool air of the morning.  I noticed that Larry Riley gave me a slightly worried look and I wondered what it meant.  I realized what it was moments later when I went to remove the respirator off of my face.  I only had one filter cartridge in the respirator.

Half-face respirator

The other one was missing.  I thought that was silly of me to go in there with only one filter.  No wonder it seemed like I was breathing a lot of dust.  Then I thought…. No.  I know I had both filters when I went in the duct.  I must have lost one while I was in there.  Maybe with all that banging I knocked it off.

Anyway, 10 minutes later it was time for me to go back in there, and this time I made sure my filters were securely screwed onto the respirator.  I worried in the back of my mind that I may have ruined my lungs for life by breathing all that silicon based fly ash because I was feeling a little out of breathe (for the next 10 years).

Anyway, halfway through my 10 minutes in the duct I reached up with my hand to make sure my filters were still tightly screwed in place, and to my astonishment, they weren’t tight.  I couldn’t screw them tight.  The respirator itself had become soft in the heat and the plastic was no longer stiff enough to keep the filter tight.  It made sense then why I had lost my filter the first time.  It must have fallen down into the abyss of darkness that was right behind me while I was banging on that slag screen.

After working on the screen for an hour or so, we took a break.  When we returned the temperature in the boiler had dropped considerably, and I was able to stay in the duct the rest of the day without having to climb in and out all the time.

Larry had an air powered needle gun brought up there and someone used that for a while cleaning the screen.  It is what it sounds like.  It has rods sticking out the end of a gun looking tool that vibrate wildly when you pull the trigger.  I don’t know what the real name is for it, but it cleaned slag screens a lot faster than my beating the screen with the rubber mallet all day.

Needle Gun

I did beat that screen all day.  When it was time to leave I brought the mallet back to the tool room, and it looked like this:

Rubber Mallet after banging on a slag screen all day

I had worn the rubber off of the  mallet.  When I brought the mallet back to the tool room, Bif said, “What is this?”  I said I was just returning the mallet that I had borrowed that morning.  He said something about how I must be some kind of a he-man or crazy.   I was too worried about my lungs to think about how much my wrists were aching from taking that pounding all day.

A couple of months later I was promoted to the Labor Crew.  Chuck Ross had kept saying that he couldn’t wait for me to go to the Labor Crew because he wanted me to work for him.  The very day that I started on the Labor Crew, the plant had a going-away party for Chuck Ross.  He was leaving our plant to go work at another one in Muskogee.

During the party Chuck presented me with the rubber mallet that I had used that day cleaning the slag screen.  He said he had never seen anything like that before.  He was sorry he was going to leave without having the opportunity to have me working for him.  I felt the same way about Chuck.  I have always kept that rubber mallet laying around the house since 1983 when I received it.  My wife sometimes picks it up when she is cleaning somewhere and says, “Do you still want this?” With a hopeful look, like someday I may say that it is all right if she throws it away.

Of course I want to keep it.  It reminds me of the days when I was able to work with True Power Plant Men in their natural environment.  The slag screen was later deemed unnecessary and was removed from the boiler.

It also reminds me of other things.  Like how quickly something can happen that changes your life forever.

Questions from that day have always remained with me.

How much ash did I breathe in?  I couldn’t see much more than a few feet in front of me as I banged on that screen knocking ash down all over me.  What did it do to my lungs?

What if I had taken a step back or slipped off of that beam before I had walked to the other end to secure my safety lanyard?  I know now what was below me then.  I would have fallen about 20 feet down to some fins, and then down another 20 feet onto the air preheater baskets.  It would have taken a while to retrieve me, once someone figured out that I was missing.

What does that much heat do to your body… or your brain?

I know these are things that go through the minds of True Power Plant Men.  I worked with them for years improving the safety of the power plant.  All-in-all, no one ever died when I was there, though some came close.  The Slogan over the Shift Supervisor’s Office said, “Safety is job #1”.  That wasn’t there to try to convince us that Safety was important.  It was there as a testimony to everyone who had already made that decision.

Angel of Death Passes by the Precipitator Door — Repost

Originally published on May 25, 2012:

Either this was the luckiest day of my life, or a day where stupidity seemed to be my natural state of mind. This particular day occurred sometime in September 1983. The Main Power transformer for Unit 1 had  shutdown because of an internal fault during an exceptionally hot day during the summer and was being replaced. While the unit was offline, while I was on the labor crew, I was asked to help out the electricians who were doing an overhaul on the Precipitator. The Precipitator takes the ash out of the boiler exhaust before it goes up the smoke stack. Without it, you would see thick smoke, instead, you see only clear exhaust. At the time the electricians I worked with were Sonny Kendrick and Bill Rivers. I had already applied for a job in the electric shop and was waiting to see if I was going to be offered the job. This gave me the chance to show the electricians what a brilliant worker I was.

Bill Rivers told me to go in the precipitator and wipe down the insulators that held the wire racks in place. He showed me where they were. I wore a regular half-face respirator because the fly ash is harmful to inhale.

Half-face respirator

Just before I went in the precipitator door to begin wiping down the insulators using a Scotch Brite Pad, Bill Rivers pointed to my flashlight and said, “Don’t drop your flashlight in a hopper otherwise you will have to make sure that you get it out of the hopper before we go back online.” I told him I would be sure to hold onto my flashlight (noticing that Bill had a string tied to his flashlight which was slung over his shoulder) and I entered the precipitator door.

Yellow Flashlight similar to the one I carried

The inside of the precipitator was dark. 70 foot tall plates are lined up 9 inches apart. Wires hang down between the plates and when the precipitator is turned on, the wires are charged up to around 45,000 volts of electricity. The wires each have a 30 pound weight on the bottom to take out the tension, and the wires are kept apart and lined up by a rack at the bottom. One end of the rack which is about 25 feet long is held in place by an electrical insulator about 3 feet long. This is what I was supposed to clean. The light from the flashlight lit up the area around me because everything was covered with the fine white powder reflecting the light.

The first hopper I came to was full of ash up to the top of the hopper, but just below where the insulator was mounted to the edge of the hopper. So, I worked my way down to the ledge along the edge of the hopper and dangled my feet down into the ash as I prepared to wipe down the first of the four insulators on this particular hopper. Just as I began, the precipitator suddenly went dark as my flashlight fell from my hand and down into the hopper. — Oh boy, that didn’t take long.

Fly Ash Hoppers. Our hoppers were 12 foot by 12 foot at the top.

I sat there for a minute in the dark as my eyes grew accustomed to the small amount of light that was coming through the doors. After I could see again, I reached my hand into the ash to feel for my flashlight. The ash was very fluffy and there was little or no resistance as I flailed my hand around searching for it. I leaned over farther and farther to reach down deeper into the ash. I was at the point where I was laying down flat on the ledge trying to find the flashlight, and it was no where to be found.

I pulled myself over to the side edge of the hopper and dropped myself down into the ash so that I could reach over where I had dropped the light, but I was still not able to find it. At that point, I was leaning out into the hopper with only my one index finger gripping the ledge around the hopper. I had a decision to make… I thought I would just bail off into the ash to see if I could find the flashlight, or I could give up and go tell Bill Rivers that I had done the one thing that he told me not to do, and in record time. I don’t usually like to give up until I have exhausted every effort, so here was my dilemma. Do I let go and dive into this ash to retrieve my flashlight? Or do I leave the hopper and go tell Bill? I regretfully decided to go tell Bill. So, I climbed up out of the hopper, with my clothes covered with Ash (as we did not have fly ash suits at the time and I was wearing my coveralls). I made my way to the precipitator door and once I was outside, I determined which hopper I had been in when I dropped my flashlight.

I found Bill and told him that I had dropped my flashlight in a hopper full of ash. He told me to get the key for that hopper and open the door at the bottom and see if I could find the flashlight. Unlike the picture of the hoppers above, we had a landing around the base of the hoppers by the access door so you didn’t need a ladder to reach them.

Curtis Love had been watching the door of the precipitator for me while I was supposed to be wiping off the insulators. He came down with me, and we proceeded to open the access door at the bottom on the side of the hopper. When I opened the door both Curtis and I were swept backward as a stream of fly ash shot from the door. The ash fell through the grating to the ground below. We regained our footing and watched as a tremendous pile of ash grew below us. If the flashlight had come out of the doorway, it would have remained on the landing since it was too big to go through the grating, but it never came out.

After the ash had finished pouring out of the hopper as if it were water, I reached down into the remaining ash to see if I could feel the flashlight. Still I was unable to find it. There was about 4 more feet from the doorway to the bottom of the hopper, so I emptied out as much ash as I could using my hard hat for a shovel. Then I pulled my body head first into the hopper and I reached down as far as I could in the bottom of the hopper, but I couldn’t find the flashlight.

So, in my infinite wisdom, I asked Curtis Love to hold onto my legs as I lowered myself down to the throat at the bottom of the hopper. I lowered myself down until I had half of my face laying in the ash. At this point only one of the two filters on my respirator was able to function as the other one was down in the ash. I reached my hand into the top of the feeder at the bottom of the hopper and with my finger tips I could just feel the flashlight. I had reached as far as I could, but I couldn’t reach far enough to grip the flashlight.

All of the sudden my head dipped down into the ash and my hand went around the flashlight. I was not able to breathe as my respirator (and my entire head) was entirely immersed in ash. Everything went dark. I struggled to get up, as Curtis had let go of my legs and I had plunged head first into the bottom of the hopper. I had one hand free as the other one held the flashlight. I used it to push against the opposite wall of the hopper to raise my head up out of the ash. I still couldn’t breathe as my respirator was now clogged solid with ash. When I tried to inhale, the respirator just gripped my face tighter. Finally with my one free hand pushing against the hopper wall to hold my head out of the ash, I reached up with the hand that held the flashlight and pushed against my respirator enough to break the seal around my face so that I was able to get a breath of air.

Then I quickly pulled myself out of the precipitator as I heard Curtis saying the mantra that I had heard one other time (as I indicated in the post about Power Plant Safety as Interpreted by Curtis Love). He was saying over and over again, “I’mSorry,I’mSorry, KevinI’mSorry, ThoseGuysWereTicklingMe. I’mSorry,IDidn’tMeanToLetGo,ITriedToHoldOn, butThoseGuysWereTicklingMe.”

Looking around I spied a few Labor Crew hands sneaking away. As this happened before when I was sandblasting in the sand filter tank when Curtis Love had turned off my air, this wasn’t the first encounter I had with Power Plant Men In-Training playing a Power Plant joke on me. I told Curtis to forget it. I had retrieved my flashlight and everything was all right. I was covered from head-to-toe with fly ash, but that washes off pretty easily.

It dawned on me then that when I had dropped the flashlight, it had sunk clear to the bottom of the hopper and down into the throat of the feeder at the bottom. If I had dived into the ash in the hopper from up above, I would have fallen right down to the bottom of the hopper and been engulfed in ash. My feet would have been pinned down in the feeder pipe, and that would have been the end of me. It probably would have taken many hours to figure out where I was, and they would have found only a corpse.

While I was hanging on the edge of the hopper with only the tip of my index finger gripping the ledge, I was actually considering letting go. There never would have been an electrician at the power Plant named Kevin Breazile. I never would have married my wife Kelly, and had my two children Elizabeth and Anthony. I would not be writing this story right now. If it had been left to my own stupidity, none of those things would have happened. I believe it was my guardian angel that had talked me out of letting go (or had actually been standing on my fingers). As stubborn as I was, and against my nature, that day I had decided to give up searching for my flashlight and seek help. That one momentary decision has made all the difference in my life.

Since that day I have had a certain appreciation for the things that happen to me even when they seem difficult at the time. I have lived a fairly stress-free life because each day is a gift. Currently I work in a stress-filled job where individual accomplishments are seldom rewarded. From one day to the next I may be laid off at any time. I still find a lot of satisfaction in what I do because it was possible that it never would have happened. I have been kept alive for a purpose so I might as well enjoy the ride.

I find a special love for the people I work with today, because they are all gifts to me. I try to pay them back with kindness… when that doesn’t work.. I try to annoy them with my presence… Just to say….. — I am still here!

Luxuries and Amenities of a Power Plant Labor Crew

When I was a janitor at the Power Plant there were times when we were christened by being allowed to work with the Labor Crew on jobs that needed to be done in a hurry.  Larry Riley was the foreman of the Labor Crew.  I had worked with Larry Riley during the summers when I was a summer help, and I always held him in high esteem.  I think he knew that, and he said he was glad to have me working for him whenever they were in a pinch to complete a job in a hurry.  I have described Larry as reminding me of the Marlboro Man, as he had a moustache that looked like his.

Yep. That’s the Marlboro Man

The wonderful thing about working in a Power Plant is that when you drive through the gate in the morning, you never know what you might be doing that day.   Even after 20 years at the plant, I was still amazed by the diversity of jobs a person could do there.  Anyone who spent those 20 years actually working instead of doing a desk job, would know a lot about all kinds of equipment and instruments, and temperatures.

When I was young I was able to go to Minnesota to visit my cousins in a place called “Phelp’s Mill”.  Named after an old mill along a river that was a “self service” museum.  Across the road and on the hill loomed a big foreboding house where my cousins lived during the summers.  We would play hide-and-seek in that mill, which was mainly made out of wood.  It was 4 stories high if you include the basement and had a lot of places to hide.

Phelps Mill, MN where we played as a boy

This is a picture of the inside of Phelps Mill by Shawn Turner: http://www.flickr.com/photos/32364049@N04/7174048516/

When I began working in the Power Plant, I realized one day that this was like that old mill only on a much bigger scale.  You could spend half of a live time wandering around that plant before you actually knew where everything was.  So, each day brought something new.  My first years as a summer help, most of the “emergencies” that I would take part in had to do with cleaning up coal.  When I was able to work with the Labor Crew, things became a lot more interesting.

One day in the spring of 1983 when I arrived at work ready to mop the floor and sweep and dust the Turbine Generators, I was told that I needed to get with Chuck Ross an A foreman over the Labor Crew at the time, because I was going to work with the Labor Crew that day.  I was told to bring my respirator… Which usually had meant it was time to shovel coal.  This day was different.

Chuck brought me to the Tool room and asked Bud Schoonover to give me a new Rubber Mallet.

New Rubber Mallet just like this

I went with the labor crew up on #1 Boiler just above the Air Preheater Baskets that I didn’t know existed at the time…  The Boiler had been shutdown over night because there was a problem with the airflow through the boiler and we had to go in the duct and clean the Slag Screen.

“Slag Screen,” I thought… That sounds like a fancy word for something that was  probably just some kind of filter or something….  I knew that Power Plant Engineers liked to give fancy words to make the Plant sound more like a Palace.  As I mentioned before… there are places like:  The Tripper Gallery.  Hopper Nozzle Booster Pump. Generator Bathtub.  The Gravimetric Feeder Deck — I liked that one, it sounded like you were on a ship.  Travelling Water Screens.  There were long names for some, like “Force Draft Fan Inboard Bearing Lube Oil Pump”.  Anyway, I could go on and on.

Larry Riley explained to us that we needed to work as fast as we could to clean the slag screen because they wanted to bring this unit back on in the evening.  We couldn’t wait for the unit to cool down much, so we were only allowed to go in the hot air duct for 10 minutes at a time.

So, in I went.  The first thing I noticed as I stuck my head in the door was that there wasn’t any immediate place to stand.  There was only a hole below me that went down into the darkness.  So I looked around for something to grab onto to pull myself in.  Once my body was in the door I was able to walk along a beam next to this big screen.  It looked similar to a screen on a window at home only the wires were about 1/2 inch apart.  Something like this:

A picture of a similar slag screen

Oh, and there was one more thing that I noticed…. It was incredibly HOT.  I was wearing leather gloves so I could grab onto the structure to hold myself up, but if I leaned against the screen with my arm, it would burn it.  I was just wearing a t-shirt.  I don’t know the exact temperature, but I have worked in similar heat at other times, and I would say that it was around 150 degrees.  I was not wearing my  hard hat because there was a strong wind blowing to try and cool the boiler down.

The problem is that we were on the tail end of the air flowing out of the boiler, and it was carrying all that heat right onto us.  At 160 degrees your hard hat will become soft so that you can squish it like a ball cap.  I was wearing Goggles as well, and that helped keep my eyes from drying out since everything else went dry the moment I stuck my head in there.

Anyway, I threw my lanyard around a pipe that ran diagonal across my path, and held onto it with one hand while with my other hand I began pounding on the screen with the rubber mallet.  I had to breathe very shallow because the air was so hot.  It gave the air time to cool off a bit before it went down into my throat.

This was a new adventure for me.  There are some Brave Power Plant Men that are on the “Bowl Mill” crew that have worked in these conditions for weeks at a time.  I suppose you grow used to it after a while.  Kind of like when you eat something with Habenero Sauce.  The first time it just very painful.  Then a few weeks later, you’re piling it on your tortilla chips.

After my first 10 minutes were over, someone at the door, (which was hard to see) hollered for me, so I made my way back to the door and emerged into the cool air of the morning.  I noticed that Larry Riley gave me a slightly worried look and I wondered what it meant.  I realized what it was moments later when I went to remove the respirator off of my face.  I only had one filter cartridge in the respirator.

Half-face respirator

The other one was missing.  I thought that was silly of me to go in there with only one filter.  No wonder it seemed like I was breathing a lot of dust.  Then I thought…. No.  I know I had both filters when I went in the duct.  I must have lost one while I was in there.  Maybe with all that banging I knocked it off.

Anyway, 10 minutes later it was time for me to go back in there, and this time I made sure my filters were securely screwed onto the respirator.  I worried in the back of my mind that I may have ruined my lungs for life by breathing all that silicon based fly ash because I was feeling a little out of breathe.

Anyway, halfway through my 10 minutes in the duct I reached up with my hand to make sure my filters were still tightly screwed in place, and to my astonishment, they weren’t tight.  I couldn’t screw them tight.  The respirator itself had become soft in the heat and the plastic was no longer stiff enough to keep the filter tight.  It made sense then why I had lost my filter the first time.  It must have fallen down into the abyss of darkness that was right behind me the entire time I was banging on that slag screen.

After working on the screen for an hour or so, we took a break.  When we returned the temperature in the boiler had dropped considerably, and I was able to stay in the duct the rest of the day without having to climb in and out all the time.

Larry had an air powered needle gun brought up there and someone used that for a while cleaning the screen.  It is what it sounds like.  It has rods sticking out the end of a gun looking tool that vibrate wildly when you pull the trigger.  I don’t know what the real name is for it, but it cleaned slag screens a lot faster than my beating the screen with the rubber mallet all day.

Needle Gun

I did beat that screen all day.  When it was time to leave I brought the mallet back to the tool room, and it looked like this:

Rubber Mallet after banging on a slag screen all day

I had worn the rubber off of the  mallet.  When I brought the mallet back to the tool room, Bif said, “What is this?”  I said I was just returning the mallet that I had borrowed that morning.  He said something about how I must be some kind of a he-man or crazy.   I was too worried about my lungs to think about how much my wrists were aching from taking that pounding all day.

A couple of months later I was promoted to the Labor Crew.  Chuck Ross had kept saying that he couldn’t wait for me to go to the Labor Crew because he wanted me to work for him.  The very day that I started on the Labor Crew the plant had a going away party for Chuck Ross, because he was leaving our plant to go work at another one.

During the party Chuck presented me with the rubber mallet that I had used that day cleaning the slag screen.  He said he had never seen anything like that before.  He was sorry he was going to leave without having the opportunity to have me working for him.  I felt the same way about Chuck.  I have always kept that rubber mallet laying around the house since 1983 when I received it.  My wife sometimes picks it up when she is cleaning somewhere and says, “Do you still want this?” With a hopeful look like someday I may say that it is all right if she throws it away.

Of course I want to keep it.  It reminds me of the days when I was able to work with True Power Plant Men in their natural environment.  The slag screen was later deemed unnecessary and was removed from the boiler.

It also reminds me of other things.  Like how quickly something can happen that changes your life forever.

Question from that day have always remained with me.

How much ash did I breathe in?  I couldn’t see much more than a few feet in front of me as I banged on that screen knocking ash down all over me.  What did it do to my lungs?

What if I had taken a step back or slipped off of that beam before I had walked to the other end to secure my safety lanyard?  I know now what was below me then.  I would have fallen about 20 feet down to some fins, and then down another 20 feet onto the air preheater baskets.  It would have taken a while to retrieve me, once someone figured out that I was missing.

What does that much heat do to your body… or your brain?

I know these are things that go through the minds of True Power Plant Men.  I worked with them for years improving the safety of the power plant.  All-in-all, no one ever died when I was there, though some came close.  The Slogan over the Shift Supervisor’s Office said, “Safety is job #1”.  That wasn’t there to try to convince us that Safety was important.  It was there as a testimony to the everyone who had already made that decision.

Angel of Death Passes by the Precipitator Door (or Almost Dying Twice in One Day)

Either this was the luckiest day of my life, or a day where stupidity seemed to be my state of mind.  This particular day occurred sometime in September 1983.  The Main Power Transformer for Unit 1 had shorted out during an exceptionally hot day during the summer and was being replaced.  While the unit was offline, while I was on the labor crew, I was asked to help out the electricians who were doing an overhaul on the Precipitator.  The Precipitator takes the ash out of the boiler exhaust before it goes up the smoke stack.  Without it, you would see thick smoke, instead, you see only clear exhaust.  At the time that was Sonny Kendrick and Bill Rivers.  I had already applied for a job in the electric shop and was waiting to see if I was going to be offered the job.  This gave me the chance to show the electricians what a brilliant worker I was.

Bill Rivers told me to go in the precipitator and wipe down the insulators that held the wire racks in place.  He showed me where they were.  I wore a regular half-face respirator because the fly ash is harmful to inhale.

Half-face respirator

Just before I went in the precipitator door to begin wiping down the insulators using a Scotch Brite Pad, Bill Rivers pointed to my flashlight and said, “Don’t drop your flashlight in a hopper otherwise you will have to make sure that you get it out of the hopper before we go back online.”  I told him I would be sure to hold onto my flashlight (noticing that Bill had a string tied to his flashlight which was slung over his head) and I entered the precipitator door.

Yellow Flashlight similar to the one I carried

The inside of the precipitator was dark.  70 foot tall plates are lined up 9 inches apart.  Wires hang down between the plates and when the precipitator is turned on, the wires are charged up to around 45,000 volts of electricity.  The wires each have a 30 pound weight on the bottom to take out the tension, and the wires are kept apart and lined up by a rack at the bottom.  One end of the rack which is about 25 feet long is held in place by an electrical insulator about 3 feet long.  This is what I was supposed to clean.  The light from the flashlight lit up the area around me because everything was covered with the fine white powder reflecting the light.

The first hopper I came to was full of ash up to the top of the hopper, but just below where the insulator was mounted to the edge of the hopper.  So, I worked my way down to the ledge along the edge of the hopper and dangled my feet down into the ash as I prepared to wipe down the first of the four insulators on this particular hopper.  Just as I began, the precipitator suddenly went dark as my flashlight fell from my hand and down into the hopper.  —  Oh boy, that didn’t take long.

Fly Ash Hoppers.  Our hoppers were 12 foot by 12 foot at the top.

I sat there for a minute in the dark as my eyes grew accustomed to the small amount of light that was coming through the doors.  After I could see again, I reached my hand into the ash to feel for my flashlight.  The ash was very fluffy and there was little or no resistance as I flailed my hand around searching for it.  I leaned over farther and farther to reach down deeper into the ash.  I was at the point where I was laying down flat on the ledge trying to find the flashlight, and it was no where to be found.

I pulled myself over to the side edge of the hopper and dropped myself down into the ash so that I could reach over where I had dropped the light, but I was still not able to find it.  At that point, I was leaning out into the hopper with only my one index finger gripping the ledge around the hopper.  At this point, I had a decision to make…  I thought I would just bail off into the ash to see if I could find the flashlight, or I could give up and go tell Bill Rivers that I had done the one thing that he told me not to do, and in record time.  I don’t usually like to give up until I have exhausted every effort, so here was my dilemma.  Do I let go and dive into this ash to retrieve my flashlight?  Or do I leave the hopper and go tell Bill?  I regretfully decided to go tell Bill.  So, I climbed up out of the hopper, with my clothes covered with Ash (as we did not have fly ash suits at the time and I was wearing my coveralls).  I made my way to the precipitator door and once I was outside, I determined which hopper I had been in when I dropped my flashlight.

I found Bill and told him that I had dropped my flashlight in a hopper full of ash.  He told me to get the key for that hopper and open the door at the bottom and see if I could find the flashlight.  Unlike the picture of the hoppers above, we had a landing around the base of the hoppers by the access door so you didn’t need a ladder to reach them.

Curtis Love had been watching the door of the precipitator for me while I was supposed to be wiping off the insulators.  He came down with me, and we proceeded to open the access door at the bottom on the side of the hopper.  When I opened the door both Curtis and I were swept backward as a stream of fly ash shot from the door.  The ash fell through the grating to the ground below.  We regained our footing and watched as a tremendous pile of ash grew below us.  If the flashlight had come out of the doorway, it would have remained on the landing since it was too big to go through the grating, but it never came out.

After the ash had finished pouring out of the hopper as if it were water, I reached down into the remaining ash to see if I could feel the flashlight.  Still I was unable to find it.  There was about 4 more feet from the doorway to the bottom of the hopper, so I emptied out as much ash as I could using my hard hat for a shovel.  Then I pulled my body head first into the hopper and I reached down as far as I could in the bottom of the hopper, but I couldn’t find the flashlight.  So, in my infinite wisdom, I asked Curtis Love to hold onto my legs as I lowered myself down to the throat at the bottom of the hopper.  I lowered myself down until I had half of my face laying in the ash.  At this point only one of the two filters on my respirator was able to function as the other one was down in the ash.  I reached my hand into the top of the feeder at the bottom of the hopper and with my finger tips I could just feel the flashlight.  I had reached as far as I could, but I couldn’t reach far enough to grip the flashlight.

All of the sudden my head dipped down into the ash and my hand went around the flashlight.  I was not able to breathe as my respirator (and my entire head) was entirely immersed in ash.  I struggled to get up, as Curtis had let go of my legs and I had plunged head first into the bottom of the hopper.  I had one hand free as the other one held the flashlight.  I used it to push against the opposite wall of the hopper to raise my head up out of the ash.  I still couldn’t breathe as my respirator was now clogged solid with ash.  When I tried to inhale, the respirator just gripped my face tighter.  Finally with my one free hand pushing against the hopper wall to hold  my head out of the ash, I reached up with the hand that held the flashlight and pushed against my respirator enough to open the seal around my face so that I was able to get a breath of air.

Then I quickly pulled myself out of the precipitator as I heard Curtis saying the mantra that I had heard one other time (as I indicated in the post about Power Plant Safety as Interpreted by Curtis Love).  He was saying over and over again, “I’mSorry,I’mSorry, KevinI’mSorry, ThoseGuysWereTicklingMe. I’mSorry,IDidn’tMeanToLetGo,ITriedToHoldOn, butThoseGuysWereTicklingMe.”  Looking around I spied a few Labor Crew hands sneaking away.  As this happened before I was sandblasting in the sand filter tank when Curtis Love had turned off my air, this was the first encounter I had with Power Plant Men In-Training playing a Power Plant joke on me.  I told Curtis to forget it.  I had retrieved my flashlight and everything was all right.  I was covered from head-to-toe with fly ash, but that washes off pretty easily.

It dawned on me then that when I had dropped the flashlight, it had sunk clear to the bottom of the hopper and down into the throat of the feeder at the bottom.  If I had dived into the ash in the hopper from up above, I would have shot right down to the bottom of the hopper and been engulfed in ash.  My feet would have been pinned down in the feeder pipe, and that would have been the end of me.  It probably would have taken many hours to figure out where I was, and they would have found only a corpse.

While I was hanging on the edge of the hopper with only the tip of my index finger gripping the ledge, I was actually considering letting go.  There never would have been an electrician at the power Plant named Kevin Breazile.  I never would have married my wife Kelly, and had my two children Elizabeth and Anthony.  I would not be writing this story right now.  If I had been left to my own stupidity, none of those things would have happened.  I believe it was my guardian angel that had talked me out of letting go.  As stubborn as I was, and against my nature, that day I had decided to give up searching for my flashlight and seek help.  That one momentary decision has made all the difference in my life.

Since that day I have had a certain appreciation for the things that happen to me even when they seem difficult at the time.   I have lived a fairly stress-free life because each day is a gift.  Currently I work in a stress-filled job where individual accomplishments are seldom rewarded.  From one day to the next I may be laid off at any time.  I still find a lot of satisfaction in what I do because it was possible that it never would have happened.  I have been kept alive for a purpose so I might as well enjoy the ride.