Cracking a Boiled Egg in the Boiler and Other Days You Wish You Could Take Back
Originally Posted on April 13, 2012:
There are some days you wish you could take back after making a grand decision that turns out to look really dumb when your decision fails. It is important to think outside the box to break new ground as long as you bring common sense along for the ride.
It seemed that during the days when I was a summer help, and even when I was a laborer on Labor Crew that in order to be promoted you had to come up with one grand idea that set you apart from the others and that also failed miserably.
It was said that the electrical supervisor there before Leroy Godfrey (I can see his face, but his name escapes me. Jackie somebody), was promoted to that position after he caused the destruction of one of the Intake pump motors (a very large pump that can pump 189,000 gallons of water per minute).
To name a couple of minor “Faux Pas” (how do you pluralize that word? I don’t know — Faux Pauses?), let me start out with the least embarrassing and less dangerous and work my way to the most embarrassing and most dangerous of three different stories of someone thinking out of the box while leaving common sense somewhere behind and maybe wishing they could take back that day.
The first two stories both involve the Electrical Supervisors of two different Power Plants.
Tom Gibson, the Electrical Supervisor from our plant was trying to find a way to keep moisture out of the Bottom Ash Overflow Sump Pumps. This was a recurring problem that required a lot of man hours to repair. The bell shaped pump would have to be pulled, the motor would have to be disassembled and dried, and new seals would have to be put in the pump to keep it from leaking.
A Bottom Ash Overflow Sump Pump or BAOSP for Short
So, Tom Gibson decided that he was going to fill the motor and pump cavity with turbine oil. All electricians knew that oil used in turbines is an insulator so electrically it wouldn’t short anything out. But something in the back of your mind automatically says that this isn’t going to work.
I remember helping to fill the motor up with oil in the Maintenance shop and hooking up some motor leads from the nearby Maintenance shop 480 volt switchgear. Needless to say, as soon as the pump was turned on, it tripped the breaker and oil began leaking from the cable grommet.
That’s when common sense tells you that the all the oil causes too much drag on the rotor which will cause a 480 motor to trip very quickly. After removing some of the oil and trying it again with a larger breaker and still having the same result Tom was satisfied that this just wasn’t going to work.
The pump and motor was sent away to a nearby electric shop to be rewound and other ways were developed by the help of our top notch machinist genius Randy Dailey who came up with a positive air pressure way to keep water out of the Bottom Ash Overflow Sump Pump and motor (also known as the BAOSP). Not much harm done and Tom Gibson didn’t feel too bad for trying something that the rest of us sort of thought was mildly insane.
The next story was told to me by my dear friend Bob Kennedy when I was working at a Gas Powered Plant in Midwest City and he was my acting foreman and backed up by the rest of the electricians as they sat there nodding their heads as Bob told this story.
So I didn’t witness this myself. This one was a little more dangerous, but still thankfully, no one was hurt. Ellis Rooks, the Electrical Supervisor needed to bump test a 4200 Volt motor and wanted to do it in place (bump testing is when you switch something on and off quickly. Usually to see which way it turns). For some reason he was not able to use the existing cables, maybe because that was the reason the motor was offline. Because one of the cables had gone to ground.
So, he decided that since the motor only pulled 5 to 10 amps he could use #10 wire (the size wire in your home) and string three of them (for the three phases of the motor) from the main High Voltage switchgear across the turbine room floor over to the motor. Now, most electricians know how many amps different size wires can generally handle. It goes like this: #14 – 15 amps, #12 – 20 amps, #10 – 30 amps, #8 – 50 amps and on down (smaller numbers mean bigger wires).
So, Ellis thought that since the motor only pulls around 5 amps, and he only wanted to bump the motor (that is, turn it on and off quickly) to watch it rotate, he thought that even though there was normally three 3 – 0 cables (pronounced three aught for 3 zeroes, very large wire) wired to the motor, this would be all right because he was only going to bump it.
This works when you are using is 120 or 220 volts
Needless to say, but I will anyway, when the motor was bumped, all that was left of the #10 wires were three black streaks of carbon across the turbine room floor where the wire used to exist before it immediately vaporized.
You see, common sense tells you that 4200 volts times 5 amps = 21,000 watts of power. However, the starting amps on a motor like this may be around 50 to 100 amps, which would equal 210 to 420 Kilowatts of power (that is, 420,000 watts or more than 2/5 of a Megawatt). Thus vaporizing the small size 10 wire that is used to wire your house.
I think until the day that Ellis Rooks retired he was still trying to figure out where he went wrong. There must have been something defective with those wires.
All right. I have given you two relatively harmless stories and now the one about cracking the boiled egg in the boiler. This happened when I was still a janitor but was loaned to the Labor Crew during outages. When the boiler would come offline for an outage, the labor crew would go in the boiler and knock down clinkers and shake tubes to clean out clinkers that had built up around the boiler tubes in the intermediate pressure area of the boiler.
Clinkers are a hard buildup of ash that can become like large rocks, and when they fall and hit you on the head, depending on the size, can knock you to the floor, which makes wearing your hardhat a must. Your hardhat doesn’t help much when the clinkers falling from some 30 feet above hits you on your shoulder, so I always tried to suck my shoulders up under my hardhat (like a turtle pulling in his arms and legs) so that only my arms were left unprotected.
It wasn’t easy looking like a pole with no shoulders, but I tried my best. I think Fred Crocker the tallest and thinnest person on Labor Crew was the best at this. This is the Reheater area of the boiler in the diagram below:
Diagram of a boiler
Before we could get into the boiler to start shaking tubes, the dynamiters would go in there first and blow up the bigger clinkers. So, for a couple of days some times, at the beginning of an overhaul, you would hear someone come over the PA system about every 20 minutes saying, “Stand Clear of Number One Boiler, We’re Gonna Blast!!!” This became so common to hear over the years that unless you were up on the boiler helping out, you didn’t pay any attention to it.
This is something that is only done at a Coal-fired Power Plant because Gas Plants don’t create Ash that turns into Clinkers. Maybe some Soot, I don’t know, but not Ash. Which brings to mind a minor joke we played on Reginald Deloney one day when he came from a gas plant to work on overhaul. Reggie automatically reminded you of Richard Pryor. He had even developed a “Richard Pryor” way of talking.
Richard Pryor trying to look like Reggie Deloney
We were going to work on a Bowl Mill motor first thing, which is down next to the boiler structure in an enclosed area. We brought our roll around large toolbox and other equipment over to the motor. Andy Tubbs and Diana Brien were there with Reggie and I. I think Gary Wehunt was there with us also.
When someone came over the PA system saying, “Stand Clear of Number Two Boiler, We’re Gonna Blast”, all of us dropped everything and ran for the door as if it was an emergency. Reggie, not knowing what was going on ran like the dickens to get out in time only to find us outside laughing at the surprised look on his face.
Like this
Anyway. That wasn’t the day that someone wished they could take back, but I thought I would throw that one in anyway so that now Reggie will wish that he could take back that day.
When I was on Labor Crew, and we were waiting on the boiler for the dynamiters to blast all the large clinkers, the engineer in charge, Ed Hutchins decided that things would go a lot quicker if all the laborers would go into the boiler and shake tubes while the dynamiters were setting their charges (which wasn’t the normal procedure. Normally we waited until the dynamiters were all done). Then we would climb out when they were ready to blast, and then go back in. So, we did that.
All 10 or so of us climbed into the boiler, and went to work rattling boiler tubes until we heard someone yell, “Fire In The Hole!!!” Then we would all head for the one entrance and climb out and wait for the blast.
The extra time it took to get all of us in the boiler and back out again actually slowed everything down. We weren’t able to get much work done each time, and everyone spent most of their time climbing in and out instead of working, including the dynamiters.
So Ed had another brilliant idea. What if we stayed in the boiler while the dynamite exploded? Then we wouldn’t be wasting valuable time climbing in and out and really wouldn’t have to stop working at all.
Of course, common sense was telling us that we didn’t want to be in an enclosed boiler while several sticks worth of dynamite all exploded nearby, so the engineer decided to prove to us how safe it was by standing just inside the entrance of the boiler with his ear plugs in his ears while the dynamite exploded.
The dynamiters at first refused to set off the charges, but after Ed and the labor crew convinced them (some members on the labor crew were anxious for Ed to try out his “brilliant idea”) that there really wouldn’t be much lost if the worst happened, they went ahead and set off the dynamite.
Needless to say…. Ed came wobbling his way out of the boiler like a cracked boiled egg and said in a shaky voice, “I don’t think that would be such a good idea.” All of us on the Labor Crew said to each other, “..As if we needed him to tell us that.” I think that may be a day that Ed Hutchins would like to take back. The day he learned the real meaning of “Concussion”. I think he was promoted shortly after that and went to work in Oklahoma City at Corporate Headquarters.
Comments from Original Post:
-
eideard April 21, 2012
When you have pallets double-stacked, you should only move them about with a pallet jack. The bottom pallet – and whatever is stacked on it – is thoroughly supported. And even if the pallet jack is powered, you aren’t likely to get in trouble with rapid acceleration.
As you would with a fork lift truck.
And the double stacked pallets are truck mirrors boxed for shipment to retailers. A couple hundred mirrors. And I dumped both pallets when I went to back up and turn into the warehouse aisle.
-
jackcurtis May 5, 2012
Modern parables like these are much too good to waste! They should be included in every freshman Congressman’s Washington Welcome Kit when he first takes office and new ‘reminder’ versions again every time he wins an election. These are wonderful essays on unintended consequences, at which our Congress is among the best!
Comments from Previous repost:
Power Plant Invocations and Imitations of Sonny Karcher
Originally Posted on June 16, 2012:
I have mentioned before that Sonny Karcher was one of the first Power Plant Men that taught me how to work my way up the ladder of Power Plant Ingenuity (In the post titled, In Memory of Sonny Karcher A True Power Plant Man). I used to come home from work after Steve Higginbotham dropped me off at the duplex where we were living at the time (see the post Steve Higginbotham and His Junky Jalopy late for the Boiler Blowdown), and my family couldn’t wait to hear what Sonny Karcher had said or done that day.
Sonny Karcher
Soon after I had arrived at the plant one day, after coming back from the coal yard, Sonny had just dropped me off at the front of the Maintenance shop where I was going to the tool room to get some tools for something we were going to do. Sonny was going to drive around behind the tool room in a yellow Cushman cart to pick up some larger equipment, and I was going to meet him there.
Like this only Yellow
As he was backing out of the shop he suddenly made a motion with his left hand. To me it looked like he was making the movement that someone would make if they were taking the lid off of a jar. I thought this meant that he wanted me to do something, but I couldn’t figure out what it was.
Various things went through my head, such as, I should get something to help remove lids from barrels. Or I needed to look inside of a jar to find one of the parts I was going to pick up. Nothing made much sense to me, so I waved for him to come back.
When he did, I asked him what he wanted me to do. He asked me what I meant. I told him that when he made that motion to open a jar, I couldn’t figure out what he wanted. So he told me. “I was just waving goodbye.”
He gave me a big smile and backed out of the shop again. Each time Sonny Karcher waved goodbye, he used a different motion with his hand. Sometimes he would look like he was twirling something on his finger. Sometimes it seemed like he was trying to get something sticky off of his fingers. Sometimes he just drew circles in the air with a couple of fingers. Other times he looked like he was giving an awkward kind of salute. Sonny made an art out of simple things like a wave goodbye.
That first summer it seemed like everyone was always munching on Sunflower seeds. There were bags of sunflower seeds everywhere you looked. Sonny already looked somewhat like a chipmunk with puffy round cheeks that formed from years of wearing a grin on his face. They were extra prominent when his cheeks were full of sunflower seeds. These were seeds still in their shells.
Power Plant Sunflower Seeds
So, it was normal to see someone take a step back while standing around talking, turn their head and drop a few sunflower seed shells from their mouth into the floor drains that were spaced evenly across the maintenance shop floor. There came a time when those drains had to be cleaned out because it seemed that every drain was packed solid full of sunflower seed shells.
Sunflowers weren’t the only items found in the drains, since chewing (or dipping) tobacco (such as Skoal) was used by a lot of the men in the Power Plant.
Just a pinch between your cheek and gums…. Never tried it myself.
Cleaning out a drain full of sunflower seeds, dipping tobacco and spit was a job that might cause a lot of people to gag, and I know I had to fight it back at the time. Most of the time I felt like I was having too much fun to get paid for working at the plant, but when it came time for cleaning out those drains, I felt like I was really working very hard for the $3.89 an hour that I was getting paid my first summer (1979) as a summer help.
But anyway, back to Sonny. I remember one evening when I came home after working with Sonny during the day, and we were sitting around the dinner table eating supper when my dad said something surprising. I don’t remember exactly what he said, but I remember what my response was. It came out before I thought what I was saying, and I said it with the same surprised smile Sonny would have. I replied, “Well S–t the bed!” With a heavy emphasis on each word.
That was a common phrase that Sonny used, and it was his response to anything surprising. Needless to say, I don’t normally use four letter words that have to be edited out of a post. It was just the matter of fact way that Sonny would use that phrase that made it seem all right to say at the time. If I remember correctly, both my mom and my dad stared at me for a second in disbelief, then broke out laughing as they had never heard that particular phrase. It was kind of like hearing “…Bless his heart” for the first time when used following an obvious insult.
In the year 1990 the Power Plant had a program that they called, “We’ve Got the Power”. I will talk more about this in a later post, so I will just say that it was a program where we broke up into teams and tried to find ways to save the company money. But long before “We’ve Got the Power”, there was Sonny Karcher. He was often trying to figure out how we could make electricity cheaper, or even come up with other ways of making a profit.
One day Sonny asked me this, “Kev, your smart because you learn things from all those books at school so tell me this… someone said the other day that diamonds are made out of coal. Is that true?” I told him it was. Then he said, “Well, what if we had one of those big dirt movers full of coal drive over some coal a bunch of times, would we be able to make diamonds?”
Dirt Mover full of coal
I told him that wouldn’t work because it takes a lot more pressure to make a diamond. So, he asked me if it would work if we put some coal on the railroad track and we let an entire train full of coal run over it. Would it make a diamond then? I assured him that even that wouldn’t make a diamond. He accepted it and just said, “Well, it’s too bad since we have that big pile of coal there, we ought to be able to come up with some way of turning them into diamonds.
Another time when we were cleaning out the fish baskets at the intake (a job as smelly as it sounds) next to the 4 big intake pumps. These are the pumps that pump around 189,000 gallons of water per minute each. Sonny told me how big those pumps were and how much water they pumped. Then he said, “You know, that entire boiler is there just to make steam to turn the turbine to make electricity. It seems to me that we could just take these four pumps and have them pump water through the turbine and have it turn the turbines, then we wouldn’t need those big boilers. Why don’t we do something like that?” I assured Sonny that we would never be able to make enough electricity to make up for the electricity it took to turn the pumps that were pumping the water. He shook his head and said that it just seemed to him that those pumps could turn that turbine pretty fast.
One day I watched as Sonny watched another Power Plant man walk into the shop with a new type of lunch box. It was an Igloo Little Playmate. Sonny made a comment about how neat this guy’s new lunch box was. It was a new design at the time.
One exactly like this. These were a new kind of lunch box at the time.
Sonny immediately went out and bought one. The next week he came to work with his shiny new Little Playmate lunch box. I admit. I went and bought one myself a few weeks later. But this was the beginning of a trend that I noticed with Sonny. I began to notice that Sonny seemed to pick one item from each of the people he admired, and went and bought one for himself. Or he would pick up a phrase that someone else would say, and would start using that.
At first I thought it might just be a coincidence, so I started to test my hypothesis. When I would see something new that Sonny brought to work, I would look around to see who else had one of those, and sure enough. Someone close by would have one. Then I would hear Sonny talk a certain way. His accent would change and he would say something like he was imitating someone else, and usually I could tell right away who talked like that and knew that Sonny had borrowed that phrase from that person.
Some may think that this would be annoying, but I think with Sonny it was an act of endearment. It was his way of connecting with those people that he admired. Sonny had a small yellow orange Ford truck and I figured that someone else must have a truck like that, so I started looking all around for one like it. It took me a couple of weeks, but one morning while we were carpooling our way to the power plant, we came up behind the same kind of truck that Sonny had on its way to the plant. It was green instead of yellow, but it was undoubtedly the same model of truck. It was owned by Ken Reece, who was the manager over the tool room and warehouse.
Sonny imitated a voice that had me puzzled for a while. I had checked out all the Power Plant Men around trying to figure out who Sonny was imitating. Every once in a while Sonny would change his way of talking when he was making a point where he would let his lower lip come forward and work its way left and right as he talked, and he would close one eye more than the other and talk in a strange sort of a southern drawl. I just knew he was imitating someone because it was so different than just the regular Sonny.
Finally, one day when I was walking through the shop I heard someone in the welding area talking just like Sonny would talk when he used that voice. There was no mistake. That had to be the person. I could hear every inflection in his voice and it had to be the voice that Sonny was imitating because it had been much more honed and refined to give just the right effect. So, I changed the course I was travelling so that I could make my way around to the welders to see who it was that was talking like that.
There in the middle of the welding shop was a heavier set man standing in the middle of a group of welders telling a story. Everyone was listening to him quietly just as if it was story time at the library. So, I stopped and watched. This man wasn’t wearing an Electric Company hard hat. He was wearing a Brown and Root hard hat, which indicated that he worked for the construction company that was building the plant.
This guy was undoubtedly a master storyteller. When it came to the climactic part of the story, the bottom of his mouth would stick out with his lip moving left and right and left again, and one eye was partially closed to show the intensity of the situation and the drawl would intensify. Finally. I had found the man that Sonny Karcher had admired enough to take one of his favorite traits and connect it to himself. I could see why Sonny admired him so much. He had everyone within listening distance captivated by his story.
This Brown and Root hand soon became an employee of the Electric Company within a couple of weeks after I left at the end of the summer (on September 9, 1979). This heavier set person was still working at the plant when I first posted this story last year, but has since retired. He was one of this country’s leading Turbine mechanics and he can still tell a story like no one else. He is no longer as heavy. He is rather thin in comparison. He improved his health after realizing that if he really loved his family, he needed to take better care of himself.
I consider this True Power Plant Man, Ray Eberle, to be a dear friend of mine. I have never met anyone that looked more like my own grandfather than Ray. Not that he was that much older. No. He looked almost exactly like my grandfather looked when he was Ray’s age. There was no nicer man than my dad’s dad, and there is no nicer Power Plant Man than Ray Eberle.
Ray Eberle
Comments from the re-post:
-
The Janitors at Seminole showed me how the PPM (Power Plant Men) were spitting their tobacco juice inside I-beam webs, in tight corners, and other hard to clean spots. They asked me to put out a memo asking the spitters to just spit out in the middle of the floor so they could clean it up much easier, which I did. I can’t remember for sure, but it seems like the puddles of stinky gross slime around the Plant tailed off for a while.
Good story, Kevin. I hadn’t thought about Ray Eberle for a long time. He was a super turbine man I always enjoyed being around. I just remember his competence and his positive attitude.
-
It’s both amusing, and comforting to know the same things happen at power plants everywhere, we went through a “sunflower seed phase” which plugged the drains & the plant finally came up with a “NO MORE SUNFLOWER SEEDS” rule!
Cracking a Boiled Egg in the Boiler and Other Days You Wish You Could Take Back
Originally Posted on April 13, 2012:
There are some days you wish you could take back after making a grand decision that turns out to look really dumb when your decision fails. It is important to think outside the box to break new ground as long as you bring common sense along for the ride. It seemed that during the days when I was a summer help, and even when I was a laborer on Labor Crew that in order to be promoted you had to come up with one grand idea that set you apart from the others and that also failed miserably.
It was said that the electrical supervisor there before Leroy Godfrey (I can see his face, but his name escapes me), was promoted to that position after he caused the destruction of one of the Intake pump motors (a very large pump that can pump 189,000 gallons of water per minute).
To name a couple of minor “Faux Pas” (how do you pluralize that word? I don’t know), let me start out with the least embarrassing and less dangerous and work my way to the most embarrassing and most dangerous of three different stories of someone thinking out of the box while leaving common sense somewhere behind and maybe wishing they could take back that day.
The first two stories both involve the Electrical Supervisors of two different Power Plants.
Tom Gibson, the Electrical Supervisor from our plant was trying to find a way to keep moisture out of the Bottom Ash Overflow Sump Pumps. This was a reoccurring problem that required a lot of man hours to repair. The bell shaped pump would have to be pulled, the motor would have to be disassembled and dried, and new seals would have to be put in the pump to keep it from leaking.
A Bottom Ash Overflow Sump Pump or BAOSP for Short
So, Tom Gibson decided that he was going to fill the motor and pump cavity with turbine oil. All electricians knew that oil used in turbines is an insulator so electrically it wouldn’t short anything out. But something in the back of your mind automatically says that this isn’t going to work. I remember helping to fill the motor up with oil in the Maintenance shop and hooking up some motor leads from the nearby Maintenance shop 480 volt switchgear. Needless to say, as soon as the pump was turned on, it tripped the breaker and oil began leaking from the cable grommet.
That’s when common sense tells you that the all the oil causes too much drag on the rotor which will cause a 480 motor to trip very quickly. After removing some of the oil and trying it again with a larger breaker and still having the same result Tom was satisfied that this just wasn’t going to work. The pump and motor was sent away to a nearby electric shop to be rewound and other ways were developed by the help of our top notch machinist genius Randy Dailey who came up with a positive air pressure way to keep water out of the Bottom Ash Overflow Sump Pump and motor (also known as the BAOSP). Not much harm done and Tom Gibson didn’t feel too bad for trying something that the rest of us sort of thought was mildly insane.
The next story was told to me by my dear friend Bob Kennedy when I was working at a Gas Powered Plant in Midwest City and he was my acting foreman. So I didn’t witness this myself. This one was a little more dangerous, but still thankfully, no one was hurt. Ellis Rooks, the Electrical Supervisor needed to bump test a 4200 Volt motor and wanted to do it in place. For some reason he was not able to use the existing cables, maybe because that was the reason the motor was offline. Because one of the cables had gone to ground.
So, he decided that since the motor only pulled 5 to 10 amps he could use #10 wire and string three of them (for the three phases of the motor) from the main High Voltage switchgear across the turbine room floor over to the motor. Now, most electricians know how many amps different size wires can generally handle. It goes like this: #14 – 15 amps, #12 – 20 amps, #10 – 30 amps, #8 – 50 amps and on down (smaller numbers mean bigger wires).
So, Ellis thought that since the motor only pulls around 5 amps, and he only wanted to bump the motor (that is, turn it on and off quickly) to watch it rotate, he thought that even though there was normally three 3 – 0 cables (pronounced three aught for 3 zeroes, very large wire) wired to the motor, this would be all right because he was only going to bump it.
This works when you are using is 120 or 220 volts
Needless to say, but I will anyway, when the motor was bumped, all that was left of the #10 wires were three black streaks of carbon across the turbine room floor where the wire used to exist before it immediately vaporized. You see, common sense tells you that 4200 volts times 5 amps = 21,000 watts of power. However, the starting amps on a motor like this may be around 50 to 100 amps, which would equal 210 to 420 Kilowatts of power (or about 1/5 to 2/5 of a Megawatt). Thus vaporizing the small size 10 wire that is used to wire your house.
All right. I have given you two relatively harmless stories and now the one about cracking the boiled egg in the boiler. This happened when I was still a janitor but was loaned to the Labor Crew during outages. When the boiler would come offline for an outage, the labor crew would go in the boiler and knock down clinkers and shake tubes to clean out clinkers that had built up around the boiler tubes in the intermediate pressure area of the boiler.
Clinkers are a hard buildup of ash that can become like large rocks, and when they fall and hit you on the head, depending on the size, can knock you to the floor, which makes wearing your hardhat a must. Your hardhat doesn’t help much when the clinkers falling from some 30 feet above hits you on your shoulder, so I always tried to suck my shoulders up under my hardhat (like a turtle pulling in his arms and legs) so that only my arms were left unprotected.
It wasn’t easy looking like a pole with no shoulders, but I tried my best. I think Fred Crocker the tallest and thinnest person on Labor Crew was the best at this. This is the Reheater area of the boiler in the diagram below:
Diagram of a boiler
Before we could get into the boiler to start shaking tubes, the dynamiters would go in there first and blow up the bigger clinkers. So, for a couple of days some times, at the beginning of an overhaul, you would hear someone come over the PA system about every 20 minutes saying, “Stand Clear of Number One Boiler, We’re Gonna Blast!!!” This became so common to hear over the years that unless you were up on the boiler helping out, you didn’t pay any attention to it.
This is something that is only done at a Coal-fired Power Plant because Gas Plants don’t create Ash that turns into Clinkers. Maybe some Soot, I don’t know, but not Ash. Which brings to mind a minor joke we played on Reginald Deloney one day when he came from a gas plant to work on overhaul. Reggie automatically reminded you of Richard Pryor. He had even developed a “Richard Pryor” way of talking.
Richard Pryor trying to look like Reggie Deloney
We were going to work on a Bowl Mill motor first thing, which is down next to the boiler structure in an enclosed area. We brought our large toolbox and other equipment over to the motor. Andy Tubbs and Diana Brien were there with Reggie and I. I think Gary Wehunt was there with us also.
When someone came over the PA system saying, “Stand Clear of Number Two Boiler, We’re Gonna Blast”, all of us dropped everything and ran for the door as if it was an emergency. Reggie, not knowing what was going on ran like the dickens to get out in time only to find us outside laughing at the surprised look on his face.
Like this
Anyway. That wasn’t the day that someone wished they could take back, but I thought I would throw that one in anyway so that now Reggie will wish that he could take back that day.
When I was on Labor Crew, and we were waiting on the boiler for the dynamiters to blast all the large clinkers, the engineer in charge, Ed Hutchins decided that things would go a lot quicker if all the laborers would go into the boiler and shake tubes while the dynamiters were setting their charges. Then we would climb out when they were ready to blast, and then go back in. So, we did that. All 10 or so of us climbed into the boiler, and went to work rattling boiler tubes until we heard someone yell, “Fire In The Hole!!!” Then we would all head for the one entrance and climb out and wait for the blast.
The extra time it took to get all of us in the boiler and back out again actually slowed everything down. We weren’t able to get much work done each time, and everyone spent most of their time climbing in and out instead of working, including the dynamiters. So Ed had another brilliant idea. What if we stayed in the boiler while the dynamite exploded? Then we wouldn’t be wasting valuable time climbing in and out and really wouldn’t have to stop working at all.
Of course, common sense was telling us that we didn’t want to be in an enclosed boiler while several sticks worth of dynamite all exploded nearby, so the engineer decided to prove to us how safe it was by standing just inside the entrance of the boiler with his ear plugs in his ears while the dynamite exploded. The dynamiters at first refused to set off the charges, but after Ed and the labor crew convinced them (some members on the labor crew were anxious for Ed to try out his “brilliant idea) that there really wouldn’t be much lost if the worst happened, they went ahead and set off the dynamite.
Needless to say…. Ed came wobbling his way out of the boiler like a cracked boiled egg and said in a shaky voice, “I don’t think that would be such a good idea.” All of us on the Labor Crew said to each other, “..As if we needed him to tell us that.” I think that may be a day that Ed Hutchins would like to take back. The day he learned the real meaning of “Concussion”. I think he was promoted shortly after that and went to work in Oklahoma City at Corporate Headquarters.
Comments from Original Post:
-
eideard April 21, 2012
When you have pallets double-stacked, you should only move them about with a pallet jack. The bottom pallet – and whatever is stacked on it – is thoroughly supported. And even if the pallet jack is powered, you aren’t likely to get in trouble with rapid acceleration.
As you would with a fork lift truck.
And the double stacked pallets are truck mirrors boxed for shipment to retailers. A couple hundred mirrors. And I dumped both pallets when I went to back up and turn into the warehouse aisle.
-
jackcurtis May 5, 2012
Modern parables like these are much too good to waste! They should be included in every freshman Congressman’s Washington Welcome Kit when he first takes office and new ‘reminder’ versions again every time he wins an election. These are wonderful essays on unintended consequences, at which our Congress is among the best!
Comments from Previous repost:
-
I worked with Ed on the Precipitator control replacement project (84 controls X 2) in 2006 I think. He was getting ready to retire at the time. He was a good engineer and a tough customer. I was working for the control supplier and those 168 controls were the first installation of a brand new control design. I had lead the design team for the controls and this was the culmination of our work. I spend more days and nights than I can remember going up and down the aisles of controls loading software fixes into the processors! Anyway, great people at the plant and great memories… including a rapper control cabinet that took the express route to the ground elevation from the precip roof! (ouch, it really is the sudden stop that gets you!)
-
Thanks for the comment John! It’s good to hear about improvements to the Precipitator and the control rooms I used to call home. I spend many weekends walking back and forth through those control rooms.
-
-
OMG – The very thought of a group staying in the boiler when the dynamite went off! Thank goodness THAT didn’t happen. I felt the tension just reading that bit. I’m glad Ed came out of it all right.
-
Power Plant Invocations and Imitations of Sonny Karcher
Originally Posted on June 16, 2012:
I have mentioned before that Sonny Karcher was one of the first Power Plant Men that taught me how to work my way up the ladder of Power Plant Ingenuity (In the post titled, In Memory of Sonny Karcher A True Power Plant Man). I used to come home from work after Steve Higginbotham dropped me off at the duplex where we were living at the time, and my family couldn’t wait to hear what Sonny Karcher had said or done that day.
Sonny Karcher
Soon after I had arrived at the plant one day, after coming back from the coal yard, Sonny had just dropped me off at the front of the Maintenance shop where I was going to the tool room to get some tools for something we were going to work on. Sonny was going to drive around behind the tool room in a yellow Cushman cart to pick up some larger equipment, and I was going to meet him there.
Like this only Yellow
As he was backing out of the shop he suddenly made a motion with his left hand. To me it looked like he was making the movement that someone would make if they were taking the lid off of a jar. I thought this meant that he wanted me to do something, but I couldn’t figure out what it was.
Various things went through my head, such as, I should get something to help remove lids from barrels. Or I needed to look inside of a jar to find one of the parts I was going to pick up. Nothing made much sense to me, so I waved for him to come back.
When he did, I asked him what he wanted me to do. He asked me what I meant. I told him that when he made that motion to open a jar, I couldn’t figure out what he wanted. So he told me. “I was just waving goodbye.”
He gave me a big smile and backed out of the shop again. Each time Sonny Karcher waved goodbye, he used a different motion with his hand. Sometimes he would look like he was twirling something on his finger. Sometimes it seemed like he was trying to get something sticky off of his fingers. Sometimes he just drew circles in the air with a couple of fingers. Other times he looked like he was giving an awkward kind of salute. Sonny made an art out of simple things like a wave goodbye.
That first summer it seemed like everyone was always munching on Sunflower seeds. There were bags of sunflower seeds everywhere you looked. Sonny already looked somewhat like a chipmunk with puffy round cheeks that formed from years of wearing a grin on his face. They were extra prominent when his cheeks were full of sunflower seeds. These were seeds still in their shells.
Power Plant Sunflower Seeds
So, it was normal to see someone take a step back while standing around talking, turn their head and drop a few sunflower seed shells from their mouth into the floor drains that were spaced evenly across the maintenance shop floor. There came a time when those drains had to be cleaned out because it seemed that every drain was packed solid full of sunflower seed shells.
Sunflowers weren’t the only items found in the drains, since chewing (or dipping) tobacco (such as Skoal) was used by a lot of the men in the Power Plant.
Just a pinch between your cheek and gums…. Never tried it myself.
Cleaning out a drain full of sunflower seeds, dipping tobacco and spit was a job that might cause a lot of people to gag, and I know I had to fight it back at the time. Most of the time I felt like I was having too much fun to get paid for working at the plant, but when it came time for cleaning out those drains, I felt like I was really working very hard for the $3.89 an hour that I was getting paid my first summer (1979) as a summer help.
But anyway, back to Sonny. I remember one evening when I came home after working with Sonny during the day, and we were sitting around the dinner table eating supper when my dad said something surprising. I don’t remember exactly what he said, but I remember what my response was. It came out before I thought what I was saying, and I said it with the same surprised smile Sonny would have. I replied, “Well S–t the bed!” With a heavy emphasis on each word.
That was a common phrase that Sonny used, and it was his response to anything surprising. Needless to say, I don’t normally use four letter words that have to be edited out of a post. It was just the matter of fact way that Sonny would use that phrase that made it seem all right to say at the time. If I remember correctly, both my mom and my dad stared at me for a second in disbelief, then broke out laughing as they had never heard that particular phrase. It was kind of like hearing “…Bless his heart” for the first time when used following an obvious insult.
In the year 1990 the Power Plant had a program that they called, “We’ve Got the Power”. I will talk more about this in a later post, so I will just say that it was a program where we broke up into teams and tried to find ways to save the company money. But long before “We’ve Got the Power”, there was Sonny Karcher. He was often trying to figure out how we could make electricity cheaper, or even come up with other ways of making a profit.
One day Sonny asked me this, “Kev, your smart because you learn things from all those books at school so tell me this… someone said the other day that diamonds are made out of coal. Is that true?” I told him it was. Then he said, “Well, what if we had one of those big dirt movers full of coal drive over some coal a bunch of times, would we be able to make diamonds?”
Dirt Mover full of coal
I told him that wouldn’t work because it takes a lot more pressure to make a diamond. So, he asked me if it would work if we put some coal on the railroad track and we let an entire train full of coal run over it. Would it make a diamond then? I assured him that even that wouldn’t make a diamond. He accepted it and just said, “Well, it’s too bad since we have that big pile of coal there, we ought to be able to come up with some way of making them into diamonds.
Another time when we were cleaning out the fish baskets at the intake (a job as smelly as it sounds) next to the 4 big intake pumps. These are the pumps that pump around 189,000 gallons of water per minute each. Sonny told me how big those pumps were and how much water they pumped. Then he said, “You know, that entire boiler is there just to make steam to turn the turbine to make electricity. It seems to me that we could just take these four pumps and have them pump water through the turbine and have it turn the turbines, then we wouldn’t need those big boilers. Why don’t we do something like that?” I assured Sonny that we would never be able to make enough electricity to make up for the electricity it took to turn the pumps that were pumping the water. He shook his head and said that it just seemed to him that those pumps could turn that turbine pretty fast.
One day I watched as Sonny watched another Power Plant man walk into the shop with a new type of lunch box. It was an Igloo Little Playmate. Sonny made a comment about how neat this guy’s new lunch box was. It was a new design at the time.
One exactly like this. These were a new kind of lunch box at the time.
Sonny immediately went out and bought one. The next week he came to work with his shiny new Little Playmate lunch box. I admit. I went and bought one myself a few weeks later. But this was the beginning of a trend that I noticed with Sonny. I began to notice that Sonny seemed to pick one item from each of the people he admired, and went and bought one for himself. Or he would pick up a phrase that someone else would say, and would start using that.
At first I thought it might just be a coincidence, so I started to test my hypothesis. When I would see something new that Sonny brought to work, I would look around to see who else had one of those, and sure enough. Someone close by would have one. Then I would hear Sonny talk a certain way. His accent would change and he would say something like he was imitating someone else, and usually I could tell right away who talked like that and knew that Sonny had borrowed that phrase from that person.
Some may think that this would be annoying, but I think with Sonny it was an act of endearment. It was his way of connecting with those people that he admired. Sonny had a small yellow orange Ford truck and I figured that someone else must have a truck like that, so I started looking all around for one like it. It took me a couple of weeks, but one morning while we were carpooling our way to the power plant, we came up behind the same kind of truck that Sonny had on its way to the plant. It was green instead of yellow, but it was undoubtedly the same model of truck. It was owned by Ken Reece, who was the manager over the tool room and warehouse.
Sonny imitated a voice that had me puzzled for a while. I had checked out all the Power Plant Men around trying to figure out who Sonny was imitating. Every once in a while Sonny would change his way of talking when he was making a point where he would let his lower lip come forward and work its way left and right as he talked, and he would close one eye more than the other and talk in a strange sort of a southern drawl. I just knew he was imitating someone because it was so different than just the regular Sonny.
Finally, one day when I was walking through the shop I heard someone in the welding area talking just like Sonny would talk when he used that voice. There was no mistake. That had to be the person. I could hear every inflection in his voice and it had to be the voice that Sonny was imitating because it had been much more honed and refined to give just the right effect. So, I changed the course I was travelling so that I could make my way around to the welders to see who it was that was talking like that.
There in the middle of the welding shop was a heavier set man standing in the middle of a group of welders telling a story. Everyone was listening to him quietly just as if it was story time at the library. So, I stopped and watched. This man wasn’t wearing an Electric Company hard hat. He was wearing a Brown and Root hard hat, which indicated that he worked for the construction company that was building the plant.
This guy was undoubtedly a master storyteller. When it came to the climactic part of the story, the bottom of his mouth would stick out with his lip moving left and right and left again, and one eye was partially closed to show the intensity of the situation and the drawl would intensify. Finally. I had found the man that Sonny Karcher had admired enough to take one of his favorite traits and connect it to himself. I could see why Sonny admired him so much. He had everyone within listening distance captivated by his story.
This Brown and Root hand soon became an employee of the Electric Company within a couple of weeks after I left at the end of the summer (on September 9, 1979). This heavier set person was still working at the plant when I first posted this story last year, but has since retired. He was one of this country’s leading Turbine mechanics and he can still tell a story like no one else. He is no longer as heavy. He is rather thin in comparison. He improved his health after realizing that if he really loved his family, he needed to take better care of himself.
I consider this True Power Plant Man, Ray Eberle, to be a dear friend of mine. I have never met anyone that looked more like my own grandfather than Ray. Not that he was that much older. No. He looked almost exactly like my grandfather looked when he was Ray’s age. There was no nicer man than my dad’s dad, and there is no nicer Power Plant Man than Ray Eberle.
Ray Eberle
Comments from the re-post:
-
The Janitors at Seminole showed me how the PPM (Power Plant Men) were spitting their tobacco juice inside I-beam webs, in tight corners, and other hard to clean spots. They asked me to put out a memo asking the spitters to just spit out in the middle of the floor so they could clean it up much easier, which I did. I can’t remember for sure, but it seems like the puddles of stinky gross slime around the Plant tailed off for a while.
Good story, Kevin. I hadn’t thought about Ray Eberle for a long time. He was a super turbine man I always enjoyed being around. I just remember his competence and his positive attitude.
-
It’s both amusing, and comforting to know the same things happen at power plants everywhere, we went through a “sunflower seed phase” which plugged the drains & the plant finally came up with a “NO MORE SUNFLOWER SEEDS” rule!
Power Plant Invocations and Imitations of Sonny Karcher
Originally Posted on June 16, 2012:
I have mentioned before that Sonny Karcher was one of the first Power Plant Men that taught me how to work my way up the ladder of Power Plant Ingenuity (In the post titled, In Memory of Sonny Karcher A True Power Plant Man). I used to come home from work after Steve Higginbotham dropped me off at the duplex where we were living at the time, and my family couldn’t wait to hear what Sonny Karcher had said or done that day.
Sonny Karcher
Soon after I had arrived at the plant one day, after coming back from the coal yard, Sonny had just dropped me off at the front of the Maintenance shop where I was going to the tool room to get some tools for something we were going to work on. Sonny was going to drive around behind the tool room in a yellow Cushman cart to pick up some larger equipment, and I was going to meet him there.
Like this only Yellow
As he was backing out of the shop he suddenly made a motion with his left hand. To me it looked like he was making the movement that someone would make if they were taking the lid off of a jar. I thought this meant that he wanted me to do something, but I couldn’t figure out what it was.
Various things went through my head, such as, I should get something to help remove lids from barrels. Or I needed to look inside of a jar to find one of the parts I was going to pick up. Nothing made much sense to me, so I waved for him to come back.
When he did, I asked him what he wanted me to do. He asked me what I meant. I told him that when he made that motion to open a jar, I couldn’t figure out what he wanted. So he told me. “I was just waving goodbye.”
He gave me a big smile and backed out of the shop again. Each time Sonny Karcher waved goodbye, he used a different motion with his hand. Sometimes he would look like he was twirling something on his finger. Sometimes it seemed like he was trying to get something sticky off of his fingers. Sometimes he just drew circles in the air with a couple of fingers. Other times he looked like he was giving an awkward kind of salute. Sonny made an art out of simple things like a wave goodbye.
That first summer it seemed like everyone was always munching on Sunflower seeds. There were bags of sunflower seeds everywhere you looked. Sonny already looked somewhat like a chipmunk with puffy round cheeks that formed from years of wearing a grin on his face. They were extra prominent when his cheeks were full of sunflower seeds. These were seeds still in their shells.
Power Plant Sunflower Seeds
So, it was normal to see someone take a step back while standing around talking, turn their head and drop a few sunflower seed shells from their mouth into the floor drains that were spaced evenly across the maintenance shop floor. There came a time when those drains had to be cleaned out because it seemed that every drain was packed solid full of sunflower seed shells.
Sunflowers weren’t the only items found in the drains, since chewing (or dipping) tobacco (such as Skoal) was used by a lot of the men in the Power Plant.
Just a pinch between your cheek and gums…. Never tried it myself.
Cleaning out a drain full of sunflower seeds, dipping tobacco and spit was a job that might cause a lot of people to gag, and I know I had to fight it back at the time. Most of the time I felt like I was having too much fun to get paid for working at the plant, but when it came time for cleaning out those drains, I felt like I was really working very hard for the $3.89 an hour that I was getting paid my first summer (1979) as a summer help.
But anyway, back to Sonny. I remember one evening when I came home after working with Sonny during the day, and we were sitting around the dinner table eating supper when my dad said something surprising. I don’t remember exactly what he said, but I remember what my response was. It came out before I thought what I was saying, and I said it with the same surprised smile Sonny would have. I replied, “Well S–t the bed!” With a heavy emphasis on each word.
That was a common phrase that Sonny used, and it was his response to anything surprising. Needless to say, I don’t normally use four letter words that have to be edited out of a post. It was just the matter of fact way that Sonny would use that phrase that made it seem all right to say at the time. If I remember correctly, both my mom and my dad stared at me for a second in disbelief, then broke out laughing as they had never heard that particular phrase. It was kind of like hearing “…Bless his heart” for the first time when used following an obvious insult.
In the year 1990 the Power Plant had a program that they called, “We’ve Got the Power”. I will talk more about this in a later post, so I will just say that it was a program where we broke up into teams and tried to find ways to save the company money. But long before “We’ve Got the Power”, there was Sonny Karcher. He was often trying to figure out how we could make electricity cheaper, or even come up with other ways of making a profit.
One day Sonny asked me this, “Kev, your smart because you learn things from all those books at school so tell me this… someone said the other day that diamonds are made out of coal. Is that true?” I told him it was. Then he said, “Well, what if we had one of those big dirt movers full of coal drive over some coal a bunch of times, would we be able to make diamonds?”
Dirt Mover full of coal
I told him that wouldn’t work because it takes a lot more pressure to make a diamond. So, he asked me if it would work if we put some coal on the railroad track and we let an entire train full of coal run over it. Would it make a diamond then? I assured him that even that wouldn’t make a diamond. He accepted it and just said, “Well, it’s too bad since we have that big pile of coal there, we ought to be able to come up with some way of making them into diamonds.
Another time when we were cleaning out the fish baskets at the intake (a job as smelly as it sounds) next to the 4 big intake pumps. These are the pumps that pump around 189,000 gallons of water per minute each. Sonny told me how big those pumps were and how much water they pumped. Then he said, “You know, that entire boiler is there just to make steam to turn the turbine to make electricity. It seems to me that we could just take these four pumps and have them pump water through the turbine and have it turn the turbines, then we wouldn’t need those big boilers. Why don’t we do something like that?” I assured Sonny that we would never be able to make enough electricity to make up for the electricity it took to turn the pumps that were pumping the water. He shook his head and said that it just seemed to him that those pumps could turn that turbine pretty fast.
One day I watched as Sonny watched another Power Plant man walk into the shop with a new type of lunch box. It was an Igloo Little Playmate.
One exactly like this. These were a new kind of lunch box at the time.
Sonny immediately went out and bought one. The next week he came to work with his shiny new Little Playmate lunch box. I admit. I went and bought one myself a few weeks later. But this was the beginning of a trend that I noticed with Sonny. I began to notice that Sonny seemed to pick one item from each of the people he admired, and went and bought one for himself. Or he would pick up a phrase that someone else would say, and would start using that.
At first I thought it might just be a coincidence, so I started to test my hypothesis. When I would see something new that Sonny brought to work, I would look around to see who else had one of those, and sure enough. Someone close by would have one. Then I would hear Sonny talk a certain way. His accent would change and he would say something like he was imitating someone else, and usually I could tell right away who talked like that and knew that Sonny had borrowed that phrase from that person.
Some may think that this would be annoying, but I think with Sonny it was an act of endearment. It was his way of connecting with those people that he admired. Sonny had a small yellow orange Ford truck and I figured that someone else must have a truck like that, so I started looking all around for one like it. It took me a couple of weeks, but one morning while we were carpooling our way to the power plant, we came up behind the same kind of truck that Sonny had on its way to the plant. It was green instead of yellow, but it was undoubtedly the same model of truck. It was owned by Ken Reece, who was the manager over the tool room and warehouse.
Sonny imitated a voice that had me puzzled for a while. I had checked out all the Power Plant Men around trying to figure out who Sonny was imitating. Every once in a while Sonny would change his way of talking when he was making a point where he would let his lower lip come forward and work its way left and right as he talked, and he would close one eye more than the other and talk in a strange sort of a southern drawl. I just knew he was imitating someone because it was so different than just the regular Sonny.
Finally, one day when I was walking through the shop I heard someone in the welding area talking just like Sonny would talk when he used that voice. There was no mistake. That had to be the person. I could hear every inflection in his voice and it had to be the voice that Sonny was imitating because it had been much more honed and refined to give just the right effect. So, I changed the course I was travelling so that I could make my way around to the welders to see who it was that was talking like that.
There in the middle of the welding shop was a heavier set man standing in the middle of a group of welders telling a story. Everyone was listening to him quietly just as if it was story time at the library. So, I stopped and watched. This man wasn’t wearing an Electric Company hard hat. He was wearing a Brown and Root hard hat, which indicated that he worked for the construction company that was building the plant.
This guy was undoubtedly a master storyteller. When it came to the climactic part of the story, the bottom of his mouth would stick out with his lip moving left and right and left again, and one eye was partially closed to show the intensity of the situation and the drawl would intensify. Finally. I had found the man that Sonny Karcher had admired enough to take one of his favorite traits and connect it to himself. I could see why Sonny admired him so much. He had everyone within listening distance captivated by his story.
This Brown and Root hand soon became an employee of the Electric Company within a couple of weeks after I left at the end of the summer (on September 9, 1979). This heavier set person was still working at the plant when I first posted this story last year, but has since retired. He was one of this country’s leading Turbine mechanics and he can still tell a story like no one else. He is no longer as heavy. He is rather thin in comparison. He improved his health after realizing that if he really loved his family, he needed to take better care of himself.
I consider this True Power Plant Man, Ray Eberle, to be a dear friend of mine. I have never met anyone that looked more like my own grandfather than Ray. Not that he was that much older. No. He looked almost exactly like my grandfather looked when he was Ray’s age. There was no nicer man than my dad’s dad, and there is no nicer Power Plant Man than Ray Eberle.
Ray Eberle
Comments from the re-post:
-
The Janitors at Seminole showed me how the PPM (Power Plant Men) were spitting their tobacco juice inside I-beam webs, in tight corners, and other hard to clean spots. They asked me to put out a memo asking the spitters to just spit out in the middle of the floor so they could clean it up much easier, which I did. I can’t remember for sure, but it seems like the puddles of stinky gross slime around the Plant tailed off for a while.
Good story, Kevin. I hadn’t thought about Ray Eberle for a long time. He was a super turbine man I always enjoyed being around. I just remember his competence and his positive attitude.
-
It’s both amusing, and comforting to know the same things happen at powerplants everywhere, we went through a “sunflower seed phase” which plugged the drains & the plant finally came up with a “NO MORE SUNFLOWER SEEDS” rule!
Cracking a Boiled Egg in the Boiler and Other Days You Wish You Could Take Back
Originally Posted on April 13, 2012:
There are some days you wish you could take back after making a grand decision that turns out to look really dumb when your decision fails. It is important to think outside the box to break new ground as long as you bring common sense along for the ride. It seemed that during the days when I was a summer help, and even when I was a laborer on Labor Crew that in order to be promoted you had to come up with one grand idea that set you apart from the others and that also failed miserably.
It was said that the electrical supervisor there before Leroy Godfrey (I can see his face, but his name escapes me), was promoted to that position after he caused the destruction of one of the Intake pump motors (a very large pump that can pump 189,000 gallons of water per minute).
To name a couple of minor “Faux Pas” (how do you pluralize that word? I don’t know), let me start out with the least embarrassing and less dangerous and work my way to the most embarrassing and most dangerous of three different stories of someone thinking out of the box while leaving common sense somewhere behind and maybe wishing they could take back that day.
The first two stories both involve the Electrical Supervisors of two different Power Plants.
Tom Gibson, the Electrical Supervisor from our plant was trying to find a way to keep moisture out of the Bottom Ash Overflow Sump Pumps. This was a reoccurring problem that required a lot of man hours to repair. The bell shaped pump would have to be pulled, the motor would have to be disassembled and dried, and new seals would have to be put in the pump to keep it from leaking.
A Bottom Ash Overflow Sump Pump or BAOSP for Short
So, Tom Gibson decided that he was going to fill the motor and pump cavity with turbine oil. All electricians knew that oil used in turbines is an insulator so electrically it wouldn’t short anything out. But something in the back of your mind automatically says that this isn’t going to work. I remember helping to fill the motor up with oil in the Maintenance shop and hooking up some motor leads from the nearby Maintenance shop 480 volt switchgear. Needless to say, as soon as the pump was turned on, it tripped the breaker and oil began leaking from the cable grommet. That’s when common sense tells you that the all the oil causes too much drag on the rotor which will cause a 480 motor to trip very quickly. After removing some of the oil and trying it again with a larger breaker and still having the same result Tom was satisfied that this just wasn’t going to work. The pump and motor was sent away to a nearby electric shop to be rewound and other ways were developed by the help of our top notch machinist genius Randy Dailey who came up with a positive air pressure way to keep water out of the Bottom Ash Overflow Sump Pump and motor (also known as the BAOSP). Not much harm done and Tom Gibson didn’t feel too bad for trying something that the rest of us sort of thought was mildly insane.
The next story was told to me by my dear friend Bob Kennedy when I was working at a Gas Powered Plant in Midwest City and he was my acting foreman. So I didn’t witness this myself. This one was a little more dangerous, but still thankfully, no one was hurt. Ellis Rooks, the Electrical Supervisor needed to bump test a 4200 Volt motor and wanted to do it in place. For some reason he was not able to use the existing cables, maybe because that was the reason the motor was offline. Because one of the cables had gone to ground. So, he decided that since the motor only pulled 5 to 10 amps he could use #10 wire and string three of them (for the three phases of the motor) from the main High Voltage switchgear across the turbine room floor over to the motor. Now, most electricians know how many amps different size wires can generally handle. It goes like this: #14 – 15 amps, #12 – 20 amps, #10 – 30 amps, #8 – 50 amps and on down (smaller numbers mean bigger wires). So, Ellis thought that since the motor only pulls around 5 amps, and he only wanted to bump the motor (that is, turn it on and off quickly) to watch it rotate, he thought that even though there was normally a 3 – 0 cable (pronounced three aught for 3 zeroes, very large wire), this would be ok because he was only going to bump it.
This works when you are using is 120 or 220 volts
Needless to say, but I will anyway, when the motor was bumped, all that was left were three black streaks of carbon across the turbine room floor where the wire used to exist before it immediately vaporized. You see, common sense tells you that 4200 volts times 5 amps = 21,000 watts of power. However, the starting amps on a motor like this may be around 50 to 100 amps, which would equal 210 to 420 Kilowatts of power (or about 1/5 to 2/5 of a Megawatt). Thus vaporizing the small size 10 wire that is used to wire your house.
All right. I have given you two relatively harmless stories and now the one about cracking the boiled egg in the boiler. This happened when I was still a janitor but was loaned to the Labor Crew during outages. When the boiler would come offline for an outage, the labor crew would go in the boiler and knock down clinkers and shake tubes to clean out clinkers that had built up around the boiler tubes in the intermediate pressure area of the boiler. Clinkers are a hard buildup of ash that can become like large rocks, and when they fall and hit you on the head, depending on the size, can knock you to the floor, which makes wearing your hardhat a must. Your hardhat doesn’t help much when the clinkers falling from some 30 feet above hits you on your shoulder, so I always tried to suck my shoulders up under my hardhat (like a turtle pulling in his arms and legs) so that only my arms were left unprotected. It wasn’t easy looking like a pole with no shoulders, but I tried my best. I think Fred Crocker the tallest and thinnest person on Labor Crew was the best at this. This is the Reheater area of the boiler in the diagram below:
Diagram of a boiler
Before we could get into the boiler to start shaking tubes, the dynamiters would go in there first and blow up the bigger clinkers. So, for a couple of days some times, at the beginning of an overhaul, you would hear someone come over the PA system about every 20 minutes saying, “Stand Clear of Number One Boiler, We’re Gonna Blast!!!” This became so common to hear over the years that unless you were up on the boiler helping out, you didn’t pay any attention to it.
This is something that is only done at a Coal-fired Power Plant because Gas Plants don’t create Ash that turns into Clinkers. Maybe some Soot, I don’t know, but not Ash. Which brings to mind a minor joke we played on Reginald Deloney one day when he came from a gas plant to work on overhaul. Reggie automatically reminded you of Richard Pryor. He had even developed a “Richard Pryor” way of talking.
Richard Pryor trying to look like Reggie Deloney
We were going to work on a Bowl Mill motor first thing, which is down next to the boiler structure in an enclosed area. We brought our large toolbox and other equipment over to the motor. Andy Tubbs and Diana Brien were there with Reggie and I. I think Gary Wehunt was there with us also. When someone came over the PA system saying, “Stand Clear of Number Two Boiler, We’re Gonna Blast”, all of us dropped everything and ran for the door as if it was an emergency. Reggie, not knowing what was going on ran like the dickens to get out in time only to find us outside laughing at the surprised look on his face.
Like this
Anyway. That wasn’t the day that someone wished they could take back, but I thought I would throw that one in anyway so that now Reggie will wish that he could take back that day.
When I was on Labor Crew, and we were waiting on the boiler for the dynamiters to blast all the large clinkers, the engineer in charge, Ed Hutchins decided that things would go a lot quicker if all the laborers would go into the boiler and shake tubes while the dynamiters were setting their charges. Then we would climb out when they were ready to blast, and then go back in. So, we did that. All 10 or so of us climbed into the boiler, and went to work rattling boiler tubes until we heard someone yell, “Fire In The Hole!!!” Then we would all head for the one entrance and climb out and wait for the blast.
The extra time it took to get all of us in the boiler and back out again actually slowed everything down. We weren’t able to get much work done each time, and everyone spent most of their time climbing in and out instead of working, including the dynamiters. So Ed had another brilliant idea. What if we stayed in the boiler while the dynamite exploded? Then we wouldn’t be wasting valuable time climbing in and out and really wouldn’t have to stop working at all.
Of course, common sense was telling us that we didn’t want to be in an enclosed boiler while several sticks worth of dynamite all exploded nearby, so the engineer decided to prove to us how safe it was by standing just inside the entrance of the boiler with his ear plugs in his ears while the dynamite exploded. The dynamiters at first refused to set off the charges, but after Ed and the labor crew convinced them (some members on the labor crew were anxious for Ed to try out his “brilliant idea) that there really wouldn’t be much lost if the worst happened, they went ahead and set off the dynamite.
Needless to say…. Ed came wobbling his way out of the boiler like a cracked boiled egg and said in a shaky voice, “I don’t think that would be such a good idea.” All of us on the Labor Crew said to each other, “..As if we needed him to tell us that.” I think that may be a day that Ed Hutchins would like to take back. The day he learned the real meaning of “Concussion”. I think he was promoted shortly after that and went to work in Oklahoma City at Corporate Headquarters.
Comments from Original Post:
-
eideard April 21, 2012
When you have pallets double-stacked, you should only move them about with a pallet jack. The bottom pallet – and whatever is stacked on it – is thoroughly supported. And even if the pallet jack is powered, you aren’t likely to get in trouble with rapid acceleration.
As you would with a fork lift truck.
And the double stacked pallets are truck mirrors boxed for shipment to retailers. A couple hundred mirrors. And I dumped both pallets when I went to back up and turn into the warehouse aisle.
-
jackcurtis May 5, 2012
Modern parables like these are much too good to waste! They should be included in every freshman Congressman’s Washington Welcome Kit when he first takes office and new ‘reminder’ versions again every time he wins an election. These are wonderful essays on unintended consequences, at which our Congress is among the best!
Comments from Previous repost:
-
I worked with Ed on the Precipitator control replacement project (84 controls X 2) in 2006 I think. He was getting ready to retire at the time. He was a good engineer and a tough customer. I was working for the control supplier and those 168 controls were the first installation of a brand new control design. I had lead the design team for the controls and this was the culmination of our work. I spend more days and nights than I can remember going up and down the aisles of controls loading software fixes into the processors! Anyway, great people at the plant and great memories… including a rapper control cabinet that took the express route to the ground elevation from the precip roof! (ouch, it really is the sudden stop that gets you!)
-
Thanks for the comment John! It’s good to hear about improvements to the Precipitate and the control rooms I used to call home.
-
-
OMG – The very thought of a group staying in the boiler when the dynamite went off! Thank goodness THAT didn’t happen. I felt the tension just reading that bit. I’m glad Ed came out of it all right.
-
Power Plant Invocations and Imitations of Sonny Karcher — Repost
Originally Posted on June 16, 2012:
I have mentioned before that Sonny Karcher was one of the first Power Plant Men that taught me how to work my way up the ladder of Power Plant Ingenuity (In the post titled, In Memory of Sonny Karcher A True Power Plant Man). I used to come home from work after Steve Higginbotham dropped me off at the duplex where we were living at the time, and my family couldn’t wait to hear what Sonny Karcher had said or done that day.
Soon after I had arrived at the plant Sonny had just dropped me off at the front of the Maintenance shop where I was going to the tool room to get some tools for something we were going to work on. Sonny was going to drive around behind the tool room in a yellow Cushman cart to pick up some larger equipment, and I was going to meet him there. As he was backing out of the shop he suddenly made a motion with his left hand. To me it looked like he was making the movement that someone would make if they were taking the lid off of a jar. I thought this meant that he wanted me to do something, but I couldn’t figure out what it was.
Various things went through my head, such as, I should get something to help remove lids from barrels. Or I needed to look inside of a jar to find one of the parts I was going to pick up. Nothing made much sense to me, so I waved for him to come back. When he did, I asked him what he wanted me to do. He asked me what I meant. I told him that when he made that motion to open a jar, I couldn’t figure out what he wanted. So he told me. “I was just waving goodbye.” He gave me a big smile and backed out of the shop again. Each time Sonny Karcher waved goodbye, he used a different motion with his hand. Sometimes he would look like he was twirling something on his finger. Sometimes it seemed like he was trying to get something sticky off of his fingers. Sometimes he just drew circles in the air with a couple of fingers. Other times he looked like he was giving an awkward kind of salute. Sonny made an art out of simple things like a wave goodbye.
That first summer it seemed like everyone was always munching on Sunflower seeds. There were bags of sunflower seeds everywhere you looked. Sonny already looked somewhat like a chipmunk with puffy round cheeks that formed from years of wearing a grin on his face. They were extra prominent when his cheeks were full of sunflower seeds. These were seeds still in their shells.
Power Plant Sunflower Seeds
So, it was normal to see someone take a step back while standing around talking, turn their head and drop a few sunflower seed shells from their mouth into the floor drains that were spaced evenly across the maintenance shop floor. There came a time when those drains had to be cleaned out because it seemed that every drain was packed solid full of sunflower seed shells.
Sunflowers weren’t the only items found in the drains, since chewing (or dipping) tobacco (such as Skoal) was used by a lot of the men in the Power Plant.
Just a pinch between your cheek and gums…. Never tried it myself.
Cleaning out a drain full of sunflower seeds, dipping tobacco and spit was a job that might cause a lot of people to gag, and I know I had to fight it back at the time. Most of the time I felt like I was having too much fun to get paid for working at the plant, but when it came time for cleaning out those drains, I felt like I was really working very hard for the $3.89 an hour that I was getting paid my first summer (1979) as a summer help.
But anyway, back to Sonny. I remember one evening when I came home after working with Sonny during the day, and we were sitting around the dinner table eating supper when my dad said something surprising. I don’t remember exactly what he said, but I remember what my response was. It came out before I thought what I was saying, and I said it with the same surprised smile Sonny would have. I replied, “Well S–t the bed!” With a heavy emphasis on each word. That was a common phrase that Sonny used, and it was his response to anything surprising. Needless to say, I don’t normally use four letter words that have to be edited out of a post. It was just the matter of fact way that Sonny would use that phrase that made it seem all right to say at the time. If I remember correctly, both my mom and my dad stared at me for a second in disbelief, then broke out laughing as they had never heard that particular phrase. It was kind of like hearing “…Bless his heart” for the first time used following an obvious insult.
In the year 1990 the Power Plant had a program that they called, “We’ve Got the Power”. I will talk more about this in a later post, so I will just say that it was a program where we broke up into teams and tried to find ways to save the company money. But long before “We’ve Got the Power”, there was Sonny Karcher. He was often trying to figure out how we could make electricity cheaper, or even come up with other ways of making a profit.
One day Sonny asked me this, “Kev, your smart because you learn things from all those books at school so tell me this… someone said the other day that diamonds are made out of coal. Is that true?” I told him it was. Then he said, “Well, what if we had one of those big dirt movers full of coal drive over some coal a bunch of times, would we be able to make diamonds?”
Dirt Mover full of coal
I told him that wouldn’t work because it takes a lot more pressure to make a diamond. So, he asked me if it would work if we put some coal on the railroad track and we let an entire train full of coal run over it. Would it make a diamond then? I assured him that even that wouldn’t make a diamond. He accepted it and just said, “Well, it’s too bad since we have that big pile of coal there, we ought to be able to come up with some way of making them into diamonds.
Another time when we were cleaning out the fish baskets at the intake (a job as smelly as it sounds) next to the 4 big intake pumps. These are the pumps that pump around 189,000 gallons of water per minute each. Sonny told me how big those pumps were and how much water they pumped. Then he said, “You know, that entire boiler is there just to make steam to turn the turbine to make electricity. It seems to me that we could just take these four pumps and have them pump water through the turbine and have it turn the turbines, then we wouldn’t need those big boilers. Why don’t we do something like that?” I assured Sonny that we would never be able to make enough electricity to make up for the electricity it took to turn the pumps that were pumping the water. He shook his head and said that it just seemed to him that those pumps could turn that turbine pretty fast.
One day I watched as Sonny watched another Power Plant man walk into the shop with a new type of lunch box. It was an Igloo Little Playmate.
One exactly like this. These were a new kind of lunch box at the time.
Sonny immediately went out and bought one. The next week he came to work with his shiny new Little Playmate lunch box. I admit. I went and bought one myself a few weeks later. But this was the beginning of a trend that I noticed with Sonny. I began to notice that Sonny seemed to pick one item from each of the people he admired, and went and bought one for himself. Or he would pick up a phrase that someone else would say, and would start using that. At first I thought it might just be a coincidence, so I started to test my hypothesis. When I would see something new that Sonny brought to work, I would look around to see who else had one of those, and sure enough. Someone close by would have one. Then I would hear Sonny talk a certain way. His accent would change and he would say something like he was imitating someone else, and usually I could tell right away who talked like that and knew that Sonny had borrowed that phrase from that person.
Some may think that this would be annoying, but I think with Sonny it was an act of endearment. It was his way of connecting with those people that he admired. Sonny had a small yellow orange Ford truck and I figured that someone else must have a truck like that, so I started looking all around for one like it. It took me a couple of weeks, but one morning while we were carpooling are way to the power plant, we came up behind the same kind of truck that Sonny had on its way to the plant. It was green instead of yellow, but it was undoubtedly the same model of truck. It was owned by Ken Reece, who was the manager over the tool room and warehouse.
Sonny imitated a voice that had me puzzled for a while. I had checked out all the Power Plant Men around trying to figure out who Sonny was imitating. Every once in a while Sonny would change his way of talking when he was making a point where he would let his lower lip come forward and work its way left and right as he talked, and he would close one eye more than another and talk in a strange sort of a southern drawl. I just knew he was imitating someone because it was so different than just the regular Sonny.
Finally, one day when I was walking through the shop I heard someone in the welding area talking just like Sonny would talk when he used that voice. There was no mistake. That had to be the person. I could hear every inflection in his voice and it had to be the voice that Sonny was imitating because it had been much more honed and refined to give just the right effect. So, I changed the course I was travelling so that I could make my way around to the welders to see who it was that was talking like that.
There in the middle of the welding shop was a heavier set man standing in the middle of a group of welders telling a story. Everyone was listening to him quietly just as if it was story time at the library. So, I stopped and watched. This man wasn’t wearing an Electric Company hard hat. He was wearing a Brown and Root hard hat, which indicated that he worked for the construction company that was building the plant. This guy was undoubtedly a master storyteller. When it came to the climactic part of the story, the bottom of his mouth would stick out with his lip moving left and right and left again, and one eye was partially closed to show the intensity of the situation and the drawl would intensify. Finally. I had found the man that Sonny Karcher had admired enough to take one of his favorite traits and connect it to himself. I could see why Sonny admired him so much. He had everyone within listening distance captivated by his story.
This Brown and Root hand soon became an employee of the Electric Company within a couple of weeks after I left at the end of the summer (on September 9, 1979). This heavier set person was still working at the plant when I first posted this story last year, but has since retired. He was one of this country’s leading Turbine mechanics and he can still tell a story like no one else. He is no longer as heavy. He is rather thin in comparison. He improved his health after realizing that if he really loved his family, he needed to take better care of himself. I consider this True Power Plant Man, Ray Eberle, to be a dear friend of mine. I have never met anyone that looked more like my own grandfather than Ray. Not that he was that much older. No. He looked almost exactly like my grandfather looked when he was Ray’s age. There was no nicer man than my dad’s dad, and there is no nicer Power Plant Man than Ray Eberle.
Comments from the re-post:
-
The Janitors at Seminole showed me how the PPM (Power Plant Men) were spitting their tobacco juice inside I-beam webs, in tight corners, and other hard to clean spots. They asked me to put out a memo asking the spitters to just spit out in the middle of the floor so they could clean it up much easier, which I did. I can’t remember for sure, but it seems like the puddles of stinky gross slime around the Plant tailed off for a while.
Good story, Kevin. I hadn’t thought about Ray Eberle for a long time. He was a super turbine man I always enjoyed being around. I just remember his competence and his positive attitude.
-
It’s both amusing, and comforting to know the same things happen at powerplants everywhere, we went through a “sunflower seed phase” which plugged the drains & the plant finally came up with a “NO MORE SUNFLOWER SEEDS” rule!
Cracking a Boiled Egg in the Boiler and Other Days You Wish You Could Take Back — Repost
Originally Posted on April 13, 2012:
There are some days you wish you could take back after making a grand decision that turns out to look really dumb when your decision fails. It is important to think outside the box to break new ground as long as you bring common sense along for the ride. It seemed that during the days when I was a summer help, and even when I was a laborer on Labor Crew that in order to be promoted you had to come up with one grand idea that set you apart from the others and that also failed miserably.
It was said that the electrical supervisor there before Leroy Godfrey (I can see his face, but his name escapes me), was promoted to that position after he caused the destruction of one of the Intake pump motors (a very large pump that can pump 189,000 gallons of water per minute).
To name a couple of minor “Faux Pas” (how do you pluralize that word? I don’t know), let me start out with the least embarrassing and less dangerous and work my way to the most embarrassing and most dangerous of three different stories of someone thinking out of the box while leaving common sense somewhere behind and maybe wishing they could take back that day.
The first two stories both involve the Electrical Supervisors of two different Power Plants.
Tom Gibson, the Electrical Supervisor from our plant was trying to find a way to keep moisture out of the Bottom Ash Overflow Sump Pumps. This was a reoccurring problem that required a lot of man hours to repair. The bell shaped pump would have to be pulled, the motor would have to be disassembled and dried, and new seals would have to be put in the pump to keep it from leaking.
A Bottom Ash Overflow Sump Pump or BAOSP for Short
So, Tom Gibson decided that he was going to fill the motor and pump cavity with turbine oil. All electricians knew that oil used in turbines is an insulator so electrically it wouldn’t short anything out. But something in the back of your mind automatically says that this isn’t going to work. I remember helping to fill the motor up with oil in the Maintenance shop and hooking up some motor leads from the nearby Maintenance shop 480 volt switchgear. Needless to say, as soon as the pump was turned on, it tripped the breaker and oil began leaking from the cable grommet. That’s when common sense tells you that the all the oil causes too much drag on the rotor which will cause a 480 motor to trip very quickly. After removing some of the oil and trying it again with a larger breaker and still having the same result Tom was satisfied that this just wasn’t going to work. The pump and motor was sent away to a nearby electric shop to be rewound and other ways were developed by the help of our top notch machinist genius Randy Dailey who came up with a positive air pressure way to keep water out of the Bottom Ash Overflow Sump Pump and motor (also known as the BAOSP). Not much harm done and Tom Gibson didn’t feel too bad for trying something that the rest of us sort of thought was mildly insane.
The next story was told to me by my dear friend Bob Kennedy when I was working at a Gas Powered Plant in Midwest City and he was my acting foreman. So I didn’t witness this myself. This one was a little more dangerous, but still thankfully, no one was hurt. Ellis Rooks, the Electrical Supervisor needed to bump test a 4200 Volt motor and wanted to do it in place. For some reason he was not able to use the existing cables, maybe because that was the reason the motor was offline. Because one of the cables had gone to ground. So, he decided that since the motor only pulled 5 to 10 amps he could use #10 wire and string three of them (for the three phases of the motor) from the main High Voltage switchgear across the turbine room floor over to the motor. Now, most electricians know how many amps different size wires can generally handle. It goes like this: #14 – 15 amps, #12 – 20 amps, #10 – 30 amps, #8 – 50 amps and on down (smaller numbers mean bigger wires). So, Ellis thought that since the motor only pulls around 5 amps, and he only wanted to bump the motor (that is, turn it on and off quickly) to watch it rotate, he thought that even though there was normally a 3 – 0 cable (pronounced three aught for 3 zeroes, very large wire), this would be ok because he was only going to bump it.
This works when you are using is 120 or 220 volts
Needless to say, but I will anyway, when the motor was bumped, all that was left were three black streaks of carbon across the turbine room floor where the wire used to exist before it immediately vaporized. You see, common sense tells you that 4200 volts times 5 amps = 21,000 watts of power. However, the starting amps on a motor like this may be around 50 to 100 amps, which would equal 210 to 420 Kilowatts of power (or about 1/5 to 2/5 of a Megawatt). Thus vaporizing the small size 10 wire that is used to wire your house.
All right. I have given you two relatively harmless stories and now the one about cracking the boiled egg in the boiler. This happened when I was still a janitor but was loaned to the Labor Crew during outages. When the boiler would come offline for an outage, the labor crew would go in the boiler and knock down clinkers and shake tubes to clean out clinkers that had built up around the boiler tubes in the intermediate pressure area of the boiler. Clinkers are a hard buildup of ash that can become like large rocks, and when they fall and hit you on the head, depending on the size, can knock you to the floor, which makes wearing your hardhat a must. Your hardhat doesn’t help much when the clinkers falling from some 30 feet above hits you on your shoulder, so I always tried to suck my shoulders up under my hardhat (like a turtle pulling in his arms and legs) so that only my arms were left unprotected. It wasn’t easy looking like a pole with no shoulders, but I tried my best. I think Fred Crocker the tallest and thinnest person on Labor Crew was the best at this.
Before we could get into the boiler to start shaking tubes, the dynamiters would go in there first and blow up the bigger clinkers. So, for a couple of days some times, at the beginning of an overhaul, you would hear someone come over the PA system about every 20 minutes saying, “Stand Clear of Number One Boiler, We’re Gonna Blast!!!” This became so common to hear over the years that unless you were up on the boiler helping out, you didn’t pay any attention to it.
This is something that is only done at a Coal-fired Power Plant because Gas Plants don’t create Ash that turns into Clinkers. Maybe some Soot, I don’t know, but not Ash. Which brings to mind a minor joke we played on Reginald Deloney one day when he came from a gas plant to work on overhaul. We were going to work on a Bowl Mill motor first thing, which is down next to the boiler structure in an enclosed area. We brought our large toolbox and other equipment over to the motor. Andy Tubbs and Diana Brien were there with Reggie and I. I think Gary Wehunt was there with us also. When someone came over the PA system saying, “Stand Clear of Number Two Boiler, We’re Gonna Blast”, all of us dropped everything and ran for the door as if it was an emergency. Reggie, not knowing what was going on ran like the dickens to get out in time only to find us outside laughing at the surprised look on his face.
Anyway. That wasn’t the day that someone wished they could take back, but I thought I would throw that one in anyway so that now Reggie will wish that he could take back that day.
When I was on Labor Crew, and we were waiting on the boiler for the dynamiters to blast all the large clinkers, the engineer in charge, Ed Hutchins decided that things would go a lot quicker if all the laborers would go into the boiler and shake tubes while the dynamiters were setting their charges. Then we would climb out when they were ready to blast, and then go back in. So, we did that. All 10 or so of us climbed into the boiler, and went to work rattling boiler tubes until we heard someone yell, “Fire In The Hole!!!” Then we would all head for the one entrance and climb out and wait for the blast.
The extra time it took to get all of us in the boiler and back out again actually slowed everything down. We weren’t able to get much work done each time, and everyone spent most of their time climbing in and out instead of working, including the dynamiters. So Ed had another brilliant idea. What if we stayed in the boiler while the dynamite exploded? Then we wouldn’t be wasting valuable time climbing in and out and really wouldn’t have to stop working at all.
Of course, common sense was telling us that we didn’t want to be in an enclosed boiler while several sticks worth of dynamite all exploded nearby, so the engineer decided to prove to us how safe it was by standing just inside the entrance of the boiler with his ear plugs in his ears while the dynamite exploded. The dynamiters at first refused to set off the charges, but after Ed and the labor crew convinced them that there really wouldn’t be much lost if the worst happened, they went ahead and set off the dynamite.
Needless to say…. Ed came wobbling his way out of the boiler like a cracked boiled egg and said in a shaky voice, “I don’t think that would be such a good idea.” All of us on the Labor Crew said to each other, “..As if we needed him to tell us that.” I think that may be a day that Ed Hutchins would like to take back. The day he learned the real meaning of “Concussion”. I think he was promoted shortly after that and went to work in Oklahoma City at Corporate Headquarters.
Comments from the original Post:
-
When you have pallets double-stacked, you should only move them about with a pallet jack. The bottom pallet – and whatever is stacked on it – is thoroughly supported. And even if the pallet jack is powered, you aren’t likely to get in trouble with rapid acceleration.
As you would with a fork lift truck.
And the double stacked pallets are truck mirrors boxed for shipment to retailers. A couple hundred mirrors. And I dumped both pallets when I went to back up and turn into the warehouse aisle.
-
Thanks for that. I have a few of those days myself that I will probably share in later posts.
-
Modern parables like these are much too good to waste! They should be included in every freshman Congressman’s Washington Welcome Kit when he first takes office and new ‘reminder’ versions again every time he wins an election. These are wonderful essays on unintended consequences, at which our Congress is among the best!
Power Plant Invocations and Imitations of Sonny Karcher — Repost
Originally Posted on June 16, 2012:
I have mentioned before that Sonny Karcher was one of the first Power Plant Men that taught me how to work my way up the ladder of Power Plant Ingenuity (In the post titled, In Memory of Sonny Karcher A True Power Plant Man). I used to come home from work after Steve Higginbotham dropped me off at the duplex where we were living at the time, and my family couldn’t wait to hear what Sonny Karcher had said or done that day.
Soon after I had arrived at the plant Sonny had just dropped me off at the front of the Maintenance shop where I was going to the tool room to get some tools for something we were going to work on. Sonny was going to drive around behind the tool room in a yellow Cushman cart to pick up some larger equipment, and I was going to meet him there. As he was backing out of the shop he suddenly made a motion with his left hand. To me it looked like he was making the movement that someone would make if they were taking the lid off of a jar. I thought this meant that he wanted me to do something, but I couldn’t figure out what it was.
Various things went through my head, such as, I should get something to help remove lids from barrels. Or I needed to look inside of a jar to find one of the parts I was going to pick up. Nothing made much sense to me, so I waved for him to come back. When he did, I asked him what he wanted me to do. He asked me what I meant. I told him that when he made that motion to open a jar, I couldn’t figure out what he wanted. So he told me. “I was just waving goodbye.” He gave me a big smile and backed out of the shop again. Each time Sonny Karcher waved goodbye, he used a different motion with his hand. Sometimes he would look like he was twirling something on his finger. Sometimes it seemed like he was trying to get something sticky off of his fingers. Sometimes he just drew circles in the air with a couple of fingers. Other times he looked like he was giving an awkward kind of salute. Sonny made an art out of simple things like a wave goodbye.
That first summer it seemed like everyone was always munching on Sunflower seeds. There were bags of sunflower seeds everywhere you looked. Sonny already looked somewhat like a chipmunk with puffy round cheeks that formed from years of wearing a grin on his face. They were extra prominent when his cheeks were full of sunflower seeds. These were seeds still in their shells.
Power Plant Sunflower Seeds
So, it was normal to see someone take a step back while standing around talking, turn their head and drop a few sunflower seed shells from their mouth into the floor drains that were spaced evenly across the maintenance shop floor. There came a time when those drains had to be cleaned out because it seemed that every drain was packed solid full of sunflower seed shells.
Sunflowers weren’t the only items found in the drains, since chewing (or dipping) tobacco (such as Skoal) was used by a lot of the men in the Power Plant.
Just a pinch between your cheek and gums…. Never tried it myself.
Cleaning out a drain full of sunflower seeds, dipping tobacco and spit was a job that might cause a lot of people to gag, and I know I had to fight it back at the time. Most of the time I felt like I was having too much fun to get paid for working at the plant, but when it came time for cleaning out those drains, I felt like I was really working very hard for the $3.89 an hour that I was getting paid my first summer (1979) as a summer help.
But anyway, back to Sonny. I remember one evening when I came home after working with Sonny during the day, and we were sitting around the dinner table eating supper when my dad said something surprising. I don’t remember exactly what he said, but I remember what my response was. It came out before I thought what I was saying, and I said it with the same surprised smile Sonny would have. I replied, “Well S–t the bed!” With a heavy emphasis on each word. That was a common phrase that Sonny used, and it was his response to anything surprising. Needless to say, I don’t normally use four letter words that have to be edited out of a post. It was just the matter of fact way that Sonny would use that phrase that made it seem all right to say at the time. If I remember correctly, both my mom and my dad stared at me for a second in disbelief, then broke out laughing as they had never heard that particular phrase. It was kind of like hearing “…Bless his heart” for the first time used following an obvious insult.
In the year 1990 the Power Plant had a program that they called, “We’ve Got the Power”. I will talk more about this in a later post, so I will just say that it was a program where we broke up into teams and tried to find ways to save the company money. But long before “We’ve Got the Power”, there was Sonny Karcher. He was often trying to figure out how we could make electricity cheaper, or even come up with other ways of making a profit.
One day Sonny asked me this, “Kev, your smart because you learn things from all those books at school so tell me this… someone said the other day that diamonds are made out of coal. Is that true?” I told him it was. Then he said, “Well, what if we had one of those big dirt movers full of coal drive over some coal a bunch of times, would we be able to make diamonds?”
Dirt Mover full of coal
I told him that wouldn’t work because it takes a lot more pressure to make a diamond. So, he asked me if it would work if we put some coal on the railroad track and we let an entire train full of coal run over it. Would it make a diamond then? I assured him that even that wouldn’t make a diamond. He accepted it and just said, “Well, it’s too bad since we have that big pile of coal there, we ought to be able to come up with some way of making them into diamonds.
Another time when we were cleaning out the fish baskets at the intake (a job as smelly as it sounds) next to the 4 big intake pumps. These are the pumps that pump around 189,000 gallons of water per minute each. Sonny told me how big those pumps were and how much water they pumped. Then he said, “You know, that entire boiler is there just to make steam to turn the turbine to make electricity. It seems to me that we could just take these four pumps and have them pump water through the turbine and have it turn the turbines, then we wouldn’t need those big boilers. Why don’t we do something like that?” I assured Sonny that we would never be able to make enough electricity to make up for the electricity it took to turn the pumps that were pumping the water. He shook his head and said that it just seemed to him that those pumps could turn that turbine pretty fast.
One day I watched as Sonny watched another Power Plant man walk into the shop with a new type of lunch box. It was an Igloo Little Playmate.
One exactly like this. These were a new kind of lunch box at the time.
Sonny immediately went out and bought one. The next week he came to work with his shiny new Little Playmate lunch box. I admit. I went and bought one myself a few weeks later. But this was the beginning of a trend that I noticed with Sonny. I began to notice that Sonny seemed to pick one item from each of the people he admired, and went and bought one for himself. Or he would pick up a phrase that someone else would say, and would start using that. At first I thought it might just be a coincidence, so I started to test my hypothesis. When I would see something new that Sonny brought to work, I would look around to see who else had one of those, and sure enough. Someone close by would have one. Then I would hear Sonny talk a certain way. His accent would change and he would say something like he was imitating someone else, and usually I could tell right away who talked like that and knew that Sonny had borrowed that phrase from that person.
Some may think that this would be annoying, but I think with Sonny it was an act of endearment. It was his way of connecting with those people that he admired. Sonny had a small yellow orange Ford truck and I figured that someone else must have a truck like that, so I started looking all around for one like it. It took me a couple of weeks, but one morning while we were carpooling are way to the power plant, we came up behind the same kind of truck that Sonny had on its way to the plant. It was green instead of yellow, but it was undoubtedly the same model of truck. It was owned by Ken Reece, who was the manager over the tool room and warehouse.
Sonny imitated a voice that had me puzzled for a while. I had checked out all the Power Plant Men around trying to figure out who Sonny was imitating. Every once in a while Sonny would change his way of talking when he was making a point where he would let his lower lip come forward and work its way left and right as he talked, and he would close one eye more than another and talk in a strange sort of a southern drawl. I just knew he was imitating someone because it was so different than just the regular Sonny.
Finally, one day when I was walking through the shop I heard someone in the welding area talking just like Sonny would talk when he used that voice. There was no mistake. That had to be the person. I could hear every inflection in his voice and it had to be the voice that Sonny was imitating because it had been much more honed and refined to give just the right effect. So, I changed the course I was travelling so that I could make my way around to the welders to see who it was that was talking like that.
There in the middle of the welding shop was a heavier set man standing in the middle of a group of welders telling a story. Everyone was listening to him quietly just as if it was story time at the library. So, I stopped and watched. This man wasn’t wearing an Electric Company hard hat. He was wearing a Brown and Root hard hat, which indicated that he worked for the construction company that was building the plant. This guy was undoubtedly a master storyteller. When it came to the climactic part of the story, the bottom of his mouth would stick out with his lip moving left and right and left again, and one eye was partially closed to show the intensity of the situation and the drawl would intensify. Finally. I had found the man that Sonny Karcher had admired enough to take one of his favorite traits and connect it to himself. I could see why Sonny admired him so much. He had everyone within listening distance captivated by his story.
This Brown and Root hand soon became an employee of the Electric Company within a couple of weeks after I left at the end of the summer (on September 9, 1979). This heavier set person was still working at the plant when I first posted this story last year, but has since retired. He was one of this country’s leading Turbine mechanics and he can still tell a story like no one else. He is no longer as heavy. He is rather thin in comparison. He improved his health after realizing that if he really loved his family, he needed to take better care of himself. I consider this True Power Plant Man, Ray Eberle, to be a dear friend of mine. I have never met anyone that looked more like my own grandfather than Ray. Not that he was that much older. No. He looked almost exactly like my grandfather looked when he was Ray’s age. There was no nicer man than my dad’s dad, and there is no nicer Power Plant Man than Ray Eberle.
Cracking a Boiled Egg in the Boiler and Other Days You Wish You Could Take Back — Repost
Originally Posted on April 13, 2012:
There are some days you wish you could take back after making a grand decision that turns out to look really dumb when your decision fails. It is important to think outside the box to break new ground as long as you bring common sense along for the ride. It seemed that during the days when I was a summer help, and even when I was a laborer on Labor Crew that in order to be promoted you had to come up with one grand idea that set you apart from the others and that also failed miserably.
It was said that the electrical supervisor there before Leroy Godfrey (I can see his face, but his name escapes me), was promoted to that position after he caused the destruction of one of the Intake pump motors (a very large pump that can pump 189,000 gallons of water per minute).
To name a couple of minor “Faux Pas” (how do you pluralize that word? I don’t know), let me start out with the least embarrassing and less dangerous and work my way to the most embarrassing and most dangerous of three different stories of someone thinking out of the box while leaving common sense somewhere behind and maybe wishing they could take back that day.
The first two stories both involve the Electrical Supervisors of two different Power Plants.
Tom Gibson, the Electrical Supervisor from our plant was trying to find a way to keep moisture out of the Bottom Ash Overflow Sump Pumps. This was a reoccurring problem that required a lot of man hours to repair. The bell shaped pump would have to be pulled, the motor would have to be disassembled and dried, and new seals would have to be put in the pump to keep it from leaking.
A Bottom Ash Overflow Sump Pump or BAOSP for Short
So, Tom Gibson decided that he was going to fill the motor and pump cavity with turbine oil. All electricians knew that oil used in turbines is an insulator so electrically it wouldn’t short anything out. But something in the back of your mind automatically says that this isn’t going to work. I remember helping to fill the motor up with oil in the Maintenance shop and hooking up some motor leads from the nearby Maintenance shop 480 volt switchgear. Needless to say, as soon as the pump was turned on, it tripped the breaker and oil began leaking from the cable grommet. That’s when common sense tells you that the all the oil causes too much drag on the rotor which will cause a 480 motor to trip very quickly. After removing some of the oil and trying it again with a larger breaker and still having the same result Tom was satisfied that this just wasn’t going to work. The pump and motor was sent away to a nearby electric shop to be rewound and other ways were developed by the help of our top notch machinist genius Randy Dailey who came up with a positive air pressure way to keep water out of the Bottom Ash Overflow Sump Pump and motor (also known as the BAOSP). Not much harm done and Tom Gibson didn’t feel too bad for trying something that the rest of us sort of thought was mildly insane.
The next story was told to me by my dear friend Bob Kennedy when I was working at a Gas Powered Plant in Midwest City and he was my acting foreman. So I didn’t witness this myself. This one was a little more dangerous, but still thankfully, no one was hurt. Ellis Rooks, the Electrical Supervisor needed to bump test a 4200 Volt motor and wanted to do it in place. For some reason he was not able to use the existing cables, maybe because that was the reason the motor was offline. Because one of the cables had gone to ground. So, he decided that since the motor only pulled 5 to 10 amps he could use #10 wire and string three of them (for the three phases of the motor) from the main High Voltage switchgear across the turbine room floor over to the motor. Now, most electricians know how many amps different size wires can generally handle. It goes like this: #14 – 15 amps, #12 – 20 amps, #10 – 30 amps, #8 – 50 amps and on down (smaller numbers mean bigger wires). So, Ellis thought that since the motor only pulls around 5 amps, and he only wanted to bump the motor (that is, turn it on and off quickly) to watch it rotate, he thought that even though there was normally a 3 – 0 cable (pronounced three aught for 3 zeroes, very large wire), this would be ok because he was only going to bump it.
This works when you are using is 120 or 220 volts
Needless to say, but I will anyway, when the motor was bumped, all that was left were three black streaks of carbon across the turbine room floor where the wire used to exist before it immediately vaporized. You see, common sense tells you that 4200 volts times 5 amps = 21,000 watts of power. However, the starting amps on a motor like this may be around 50 to 100 amps, which would equal 210 to 420 Kilowatts of power (or about 1/5 to 2/5 of a Megawatt). Thus vaporizing the small size 10 wire that is used to wire your house.
All right. I have given you two relatively harmless stories and now the one about cracking the boiled egg in the boiler. This happened when I was still a janitor but was loaned to the Labor Crew during outages. When the boiler would come offline for an outage, the labor crew would go in the boiler and knock down clinkers and shake tubes to clean out clinkers that had built up around the boiler tubes in the intermediate pressure area of the boiler. Clinkers are a hard buildup of ash that can become like large rocks, and when they fall and hit you on the head, depending on the size, can knock you to the floor, which makes wearing your hardhat a must. Your hardhat doesn’t help much when the clinkers falling from some 30 feet above hits you on your shoulder, so I always tried to suck my shoulders up under my hardhat (like a turtle pulling in his arms and legs) so that only my arms were left unprotected. It wasn’t easy looking like a pole with no shoulders, but I tried my best. I think Fred Crocker the tallest and thinnest person on Labor Crew was the best at this.
Before we could get into the boiler to start shaking tubes, the dynamiters would go in there first and blow up the bigger clinkers. So, for a couple of days some times, at the beginning of an overhaul, you would hear someone come over the PA system about every 20 minutes saying, “Stand Clear of Number One Boiler, We’re Gonna Blast!!!” This became so common to hear over the years that unless you were up on the boiler helping out, you didn’t pay any attention to it.
This is something that is only done at a Coal-fired Power Plant because Gas Plants don’t create Ash that turns into Clinkers. Maybe some Soot, I don’t know, but not Ash. Which brings to mind a minor joke we played on Reginald Deloney one day when he came from a gas plant to work on overhaul. We were going to work on a Bowl Mill motor first thing, which is down next to the boiler structure in an enclosed area. We brought our large toolbox and other equipment over to the motor. Andy Tubbs and Diana Brien were there with Reggie and I. I think Gary Wehunt was there with us also. When someone came over the PA system saying, “Stand Clear of Number Two Boiler, We’re Gonna Blast”, all of us dropped everything and ran for the door as if it was an emergency. Reggie, not knowing what was going on ran like the dickens to get out in time only to find us outside laughing at the surprised look on his face.
Anyway. That wasn’t the day that someone wished they could take back, but I thought I would throw that one in anyway so that now Reggie will wish that he could take back that day.
When I was on Labor Crew, and we were waiting on the boiler for the dynamiters to blast all the large clinkers, the engineer in charge, Ed Hutchins decided that things would go a lot quicker if all the laborers would go into the boiler and shake tubes while the dynamiters were setting their charges. Then we would climb out when they were ready to blast, and then go back in. So, we did that. All 10 or so of us climbed into the boiler, and went to work rattling boiler tubes until we heard someone yell, “Fire In The Hole!!!” Then we would all head for the one entrance and climb out and wait for the blast.
The extra time it took to get all of us in the boiler and back out again actually slowed everything down. We weren’t able to get much work done each time, and everyone spent most of their time climbing in and out instead of working, including the dynamiters. So Ed had another brilliant idea. What if we stayed in the boiler while the dynamite exploded? Then we wouldn’t be wasting valuable time climbing in and out and really wouldn’t have to stop working at all.
Of course, common sense was telling us that we didn’t want to be in an enclosed boiler while several sticks worth of dynamite all exploded nearby, so the engineer decided to prove to us how safe it was by standing just inside the entrance of the boiler with his ear plugs in his ears while the dynamite exploded. The dynamiters at first refused to set off the charges, but after Ed and the labor crew convinced them that there really wouldn’t be much lost if the worst happened, they went ahead and set off the dynamite.
Needless to say…. Ed came wobbling his way out of the boiler like a cracked boiled egg and said in a shaky voice, “I don’t think that would be such a good idea.” All of us on the Labor Crew said to each other, “..As if we needed him to tell us that.” I think that may be a day that Ed Hutchins would like to take back. The day he learned the real meaning of “Concussion”. I think he was promoted shortly after that and went to work in Oklahoma City at Corporate Headquarters.
Comments from the original Post:
-
When you have pallets double-stacked, you should only move them about with a pallet jack. The bottom pallet – and whatever is stacked on it – is thoroughly supported. And even if the pallet jack is powered, you aren’t likely to get in trouble with rapid acceleration.
As you would with a fork lift truck.
And the double stacked pallets are truck mirrors boxed for shipment to retailers. A couple hundred mirrors. And I dumped both pallets when I went to back up and turn into the warehouse aisle.
-
Thanks for that. I have a few of those days myself that I will probably share in later posts.
-
Modern parables like these are much too good to waste! They should be included in every freshman Congressman’s Washington Welcome Kit when he first takes office and new ‘reminder’ versions again every time he wins an election. These are wonderful essays on unintended consequences, at which our Congress is among the best!
Power Plant Men 
I worked with Ed on the Precipitator control replacement project (84 controls X 2) in 2006 I think. He was getting ready to retire at the time. He was a good engineer and a tough customer. I was working for the control supplier and those 168 controls were the first installation of a brand new control design. I had lead the design team for the controls and this was the culmination of our work. I spend more days and nights than I can remember going up and down the aisles of controls loading software fixes into the processors! Anyway, great people at the plant and great memories… including a rapper control cabinet that took the express route to the ground elevation from the precip roof! (ouch, it really is the sudden stop that gets you!)
Thanks for the comment John! It’s good to hear about improvements to the Precipitator and the control rooms I used to call home. I spend many weekends walking back and forth through those control rooms.
OMG – The very thought of a group staying in the boiler when the dynamite went off! Thank goodness THAT didn’t happen. I felt the tension just reading that bit. I’m glad Ed came out of it all right.